-20%
aFe POWER Magnum FORCE Stage-2 Pro 5R Cold Air Intake Sys 14-19 Chevrolet Corvette (C7) V8-6.2L aFe AFE54-13041R
aFe POWER Magnum FORCE Stage-2 Pro 5R Cold Air Intake Sys 14-19 Chevrolet Corvette (C7) V8-6.2L aFe AFE54-13041R
aFe POWER Magnum FORCE Stage-2 Pro 5R Cold Air Intake Sys 14-19 Chevrolet Corvette (C7) V8-6.2L aFe AFE54-13041R
aFe POWER Magnum FORCE Stage-2 Pro 5R Cold Air Intake Sys 14-19 Chevrolet Corvette (C7) V8-6.2L aFe AFE54-13041R
aFe POWER Magnum FORCE Stage-2 Pro 5R Cold Air Intake Sys 14-19 Chevrolet Corvette (C7) V8-6.2L aFe AFE54-13041R
aFe POWER Magnum FORCE Stage-2 Pro 5R Cold Air Intake Sys 14-19 Chevrolet Corvette (C7) V8-6.2L aFe AFE54-13041R
aFe POWER Magnum FORCE Stage-2 Pro 5R Cold Air Intake Sys 14-19 Chevrolet Corvette (C7) V8-6.2L aFe AFE54-13041R
Click to zoom in

aFe Chevrolet Corvette C7 Pro 5R Stage-2 Intake

aFe
AFE54-13041R
802959545676
Cold Air Intakes
50 Units In Stock
$ 483.75 $ 387.00
$ 387.00

Chevrolet Corvette C7 Stage-2 intake details

aFe 54-13041R is a Magnum FORCE Stage-2 open-element intake for the qualified Chevrolet Corvette C7 Stingray and Grand Sport 6.2L applications below. One Pro 5R filter fits an XLPE housing connected to the factory fender-well intake tract. The XLPE tube includes a resonance chamber and aluminum vent fittings, with an alternative plug for a vehicle having only one vent connection. The illustrated installation also replaces a short hard coolant line for hood-vent clearance.

Key Features

  • One seven-inch-tall, four-inch-flange Pro 5R filter; five pre-oiled cotton-gauze layers.
  • XLPE rotomolded tube with resonance chamber and XLPE open-element housing.
  • Connects to the original fender-well intake tract and reuses factory mounting points.
  • Retains the original MAF sensor and its O-ring, using two supplied M4 x 0.7 x 8 mm screws.
  • Two aluminum vent fittings and one 1/8-inch NPT plug accommodate the actual one- or two-vent arrangement.
  • Includes coolant hose, two mini clamps and cable tie for the illustrated coolant-line replacement.
  • Selected-media bench flow: 685 versus stock 485 CFM at 7 inches H2O; calculated 41.24% increase.

Fitment

The current exact manufacturer page covers Corvette C7 2014-2019 V8-6.2L; the own manual specifically names Corvette Stingray and expressly includes Grand Sport models. Original Stingray 2014-2019 and Grand Sport 2017-2019 rows are retained. Exact selected-part retailer tables support a separate Z51 2014-2016 row; later Z51 bounds are not inferred. Some exact retailer tables also list Z06/ZR1, but the specific primary Stingray/Grand Sport scope does not resolve those other engine/housing configurations: those positive source conflicts remain held without new mappings or a physical-incompatibility claim. No C8 or related-intake inference is used.

Years Make Model Named trim; actual engine and hood requirements apply
2017-2019 Chevrolet Corvette Grand Sport
2014-2019 Chevrolet Corvette Stingray
2014-2016 Chevrolet Corvette Z51

Verify 54-13041R against the actual engine, sensor and vent connections, mounting locations and applicable emissions requirements before ordering.

Specifications

Brand aFe POWER
Manufacturer Part Number 54-13041R
System Magnum FORCE Stage-2; Pro 5R
Filter One 24-90115; 7-inch height, 4-inch flange
Media Five cotton-gauze layers; pre-oiled
Tube/housing XLPE polymer; tube has resonance chamber
Coupling 05-01375 silicone bellows; 3-7/8-inch size
Vent ports Two supplied aluminum fittings; 1/8-inch NPT plug used for unused port on one-vent vehicles
Coolant hose 3/8-inch ID, 15-inch length; replaces specified short hard line
Bench flow 685 versus stock 485 CFM at 7 inches H2O; calculated 41.24% increase
Dyno comparison At the marked 5,571 rpm, 411.1/394.5 HP and 387.5/371.9 lb-ft differ by 16.6 HP and 15.6 lb-ft. Legend maxima instead differ by 20.0 HP and 11.1 lb-ft (422.2/402.2 HP; 420.6/409.5 lb-ft). The actual manufacturer-linked sheet states SAE correction and smoothing 5 but prints no test date, vehicle identity, gear, exhaust configuration or detailed run legend. It supports that plotted comparison, not guaranteed gains on every vehicle.
Installation qualification Specific manual requires cutting the short hard coolant line; generic no-cutting product-page wording does not describe that step
Emissions Exact manufacturer page/manual: not CARB exempt; not available for purchase in California or use on a California-registered vehicle
Recheck 100-200 miles; no numeric clamp or sensor-screw torque supplied

What's Included

Quantity Manufacturer service part Component
1 24-90115 Selected Pro 5R filter
1 05-5413041B1 XLPE rotomolded tube
1 05-5413041B2 XLPE rotomolded housing
1 05-01375 Silicone bellows coupling, 3-7/8 inch
2 03-50002 Size 060 clamps
2 05-01692 Aluminum vent fittings
1 03-50410 1/8-inch NPT hex-socket plug
1 05-01507 30.5-inch trim seal
2 03-50491 T20 Torx M4 x 0.7 x 8 mm screws
1 05-01357 3/8-inch-ID coolant hose, 15-inch length
2 03-50025 Mini size 006 clamps
1 05-60167 Nylon cable tie

The shared bill shows alternative media, not two filters in the selected kit. Reuse the original MAF sensor and its O-ring, three housing mounting grommets, two original airbox mounting screws and original vent hose(s). Reinstall the radiator air outlet channel with its original four screws. The filter flange clamp is separate from the two coupling clamps. No new MAF sensor, replacement MAF O-ring or new housing mounting grommets are itemized.

About aFe Power

aFe Power develops application-specific intake, filtration, exhaust, cooling, tuning, suspension, drivetrain, and truck-performance components supported by product testing and documented installation requirements.

Related Parts

Frequently Asked Questions

Which Corvette application is covered for 54-13041R?

The qualified C7 6.2L Stingray and Grand Sport application, with the separately supported Z51 row shown in fitment. Other retailer engine/housing claims require reconciliation.

Does this kit include both filter media?

No. This selection includes one 24-90115 Pro 5R filter; the shared manual lists the other media as an alternative.

Is installation completely free of cutting?

The specific illustrated manual requires slicing both ends of the short hard coolant line between the check valve and T-fitting and replacing it with the supplied hose. This qualifies the generic no-cutting product-page wording.

How must the coolant hose be secured?

Work only on a cold engine. Fit both mini clamps; route the replacement hose above or below the intake as illustrated and tie it to the vent hose so it cannot contact the serpentine belt or pulley.

What happens to the original MAF sensor seal?

Transfer the original MAF sensor with its factory O-ring and secure it using the two supplied M4 x 0.7 x 8 mm screws. No new sensor or O-ring is itemized.

What if the vehicle has only one vent hose?

Use the appropriate supplied aluminum fitting for that connection and the supplied 1/8-inch NPT plug to close the extra port. Match the actual original arrangement.

Which end of the tube is installed first?

Insert the tube into the filter first, then fit its bellows coupling over the throttle body. Align the assembly before tightening the clamps.

What battery, torque and recheck instructions apply?

Disconnect the negative battery terminal before proceeding. The manual supplies no numeric clamp/sensor torque and requires checking bolts, clamps and connectors after 100-200 miles.

Installation Instructions

Verify aFe 54-13041R. Read the full illustrated manual, work on a cold engine and disconnect the negative battery terminal. Remove the radiator air outlet channel and retain its four screws. Disconnect the MAF harness, loosen the throttle-body/housing clamps and disconnect the original one or two vent hoses before removing the intake tube. Remove and retain the two airbox mounting screws, then lift out the original airbox. For hood-vent clearance, locate the short hard plastic coolant line between the check valve and T-fitting. With the engine cold and a shop towel below to catch excess coolant, slice open both ends of that hard line and remove it as specifically illustrated. Replace it with the supplied 3/8-inch-ID coolant hose, secure both ends with the mini clamps and use the supplied tie to secure it to the vent hose away from the serpentine belt. Snap the selected filter into the new housing from above, refit its flange clamp loose and fit the 30.5-inch top trim seal. Transfer the three original mounting grommets, press the housing assembly onto its factory stud and secure with the two original screws. Transfer the MAF sensor using the factory O-ring and two supplied M4 x 0.7 x 8 mm screws. Install the vent fittings to match equipment; on a one-vent vehicle, use the NPT plug in the unused port. Fit the silicone bellows and both clamps loosely. Insert the tube into the filter FIRST, then fit the coupling over the throttle body, align and tighten clamps. Route the coolant hose above or below the intake with the tie keeping it away from the pulley. Reconnect MAF and vent hoses, reinstall the radiator air outlet channel and verify every connection. Recheck bolts, clamps and connectors after 100-200 miles. No numeric torque is supplied.

Important Disclosures

Each own linked 16-page manual was fully read and all four contact sheets visually inspected, including the complete bill, Figures A-K and the intentionally blank page. Extracted text matches but hashes differ, so each file was inspected. Selected flow and dyno charts were visually read. At the marked 5,571 rpm, 411.1/394.5 HP and 387.5/371.9 lb-ft differ by 16.6 HP and 15.6 lb-ft. Legend maxima instead differ by 20.0 HP and 11.1 lb-ft (422.2/402.2 HP; 420.6/409.5 lb-ft). The actual manufacturer-linked sheet states SAE correction and smoothing 5 but prints no test date, vehicle identity, gear, exhaust configuration or detailed run legend. It supports that plotted comparison, not guaranteed gains on every vehicle. The manual's coolant-line cutting step takes precedence over a generic no-cutting summary. Z06/ZR1 retailer positives remain source-conflict holds; original memberships and ranges are preserved. Turn14 exact information requires unavailable authenticated access. No guaranteed output, generic filter-efficiency percentage, fixed cleaning interval, CARB exemption or price change is claimed.

California Proposition 65 warning: this product can expose you to chemicals known to the State of California to cause cancer and reproductive harm.

aFe

aFe

Shop aFe POWER intake systems, replacement filters, exhaust components, BladeRunner cooling parts and CONTROL chassis accessories at Black Ops Auto Works. Compare Momentum GT, Track Series and Magnum FORCE intake applications alongside Pro DRY S and Pro 5R filter choices. Choose a complete upgrade or a service component for the system already on your car, truck or SUV.Choose Your aFe Intake and FilterMomentum GT, Track Series and Magnum FORCECompare the intake housing, tubing, filter arrangement and finish offered for your engine. The collection includes Momentum GT applications, selected carbon-fiber Track Series systems and Magnum FORCE configurations. Each package supplies its own combination of induction components, so choose the design for the installation you want.Pro DRY S or Pro 5R Filter MediaPro DRY S uses oil-free media and skips the re-oiling step during service. Pro 5R is an oiled filter option with a different maintenance procedure. Choose a media configuration aFe off...

View aFe Products
Air Intake Systems

Air Intake Systems

Shop performance air intake systems for your next engine-bay upgrade at Black Ops Auto Works. Compare complete cold-air intakes, short-ram layouts and enclosed systems from Legmaker, JLT, aFe, K&N, Injen and other listed manufacturers. Choose the intake character, packaging and filter-service approach that suit the vehicle and the way you use it.Complete Intakes or a Focused Component UpgradeA complete intake is the place to start when changing the filter, tubing and enclosure as a matched package. An individual airbox, intake tube, coupler or replacement filter can be a better purchase when the rest of the installed system is staying. Compare what the package supplies before choosing between the two routes.For a naturally aspirated, turbocharged or supercharged engine, the connection and sensor arrangement are part of the design. Choose the complete system for that application rather than combining a large tube and filter solely by appearance.Cold-Air, Short-Ram and Enclosed De...

View Air Intake Systems Products
Chevrolet Corvette Parts & Accessories

Chevrolet Corvette Parts & Accessories

Shop Chevrolet Corvette parts for a distinctive exhaust note, carbon-fiber exterior or carefully planned engine-bay project at Black Ops Auto Works. Compare CORSA and AWE exhausts, MightyMouse catch cans, Anderson Composites panels and APR accessories. Choose the driving and appearance goals first, then build the order for the actual Corvette generation and factory equipment.CORSA and AWE Exhaust ChoicesCompare the exhaust sections changed and the sound goal before choosing cat-back, valve-back or axle-back references. CORSA packages have their own factory NPP and AFM requirements. AWE Touring and Track references offer separate sound configurations; for the supported C8 suite, Touring uses AWE’s drone-control approach while Track is the more direct sound choice. Review the exact manufacturer application and sound description for the selected system.Catch Cans, Cooling and Fuel ProjectsMightyMouse Mild systems support their stated stock or bolt-on PCV arrangements, while Wild refere...

View Chevrolet Corvette Parts & Accessories Products
Cold Air Intakes

Cold Air Intakes

Shop cold air intakes, short-ram systems, closed-airbox packages and intake tubes at Black Ops Auto Works. Compare Legmaker carbon-fiber layouts with aFe, K&N, Injen, AEM, JLT, CORSA, Volant and other listed options. Choose the filter location, inlet connection, service requirements and induction character that suit the vehicle and build.Choose the Intake LayoutA closed-airbox system encloses the filter and uses its specified air-feed arrangement. An open-element or short-ram layout places the filter differently and can change the audible induction character. A longer routed intake, a short-ram system and a factory-airbox tube replacement involve different installation scopes.Compare the actual filter position, heat-shield/enclosure design, retained ducts and access for maintenance. A cold-air label alone does not establish a lower inlet temperature in every driving condition or a fixed horsepower gain. Review manufacturer testing for the exact system and application.Legmaker HE...

View Cold Air Intakes Products
Military & First Responder Discounts

Military & First Responder Discount Program

Black Ops Auto Works proudly honors active duty military, veterans, National Guard, reserves, police officers, firefighters, and EMTs with an exclusive 5% discount on all performance parts and carbon fiber upgrades. Verify instantly and start saving today.

Learn More & Apply

Your cart

×