-20%
aFe Vulcan Series 2 1/2in 304 SS Cat-Back 19-20 Ford Edge ST V6 2.7L(tt) - aFe 49-33133
aFe Vulcan Series 2 1/2in 304 SS Cat-Back 19-20 Ford Edge ST V6 2.7L(tt) - aFe 49-33133
aFe Vulcan Series 2 1/2in 304 SS Cat-Back 19-20 Ford Edge ST V6 2.7L(tt) - aFe 49-33133
aFe Vulcan Series 2 1/2in 304 SS Cat-Back 19-20 Ford Edge ST V6 2.7L(tt) - aFe 49-33133
aFe Vulcan Series 2 1/2in 304 SS Cat-Back 19-20 Ford Edge ST V6 2.7L(tt) - aFe 49-33133
Click to zoom in

aFe Edge Sport ST 2015-2023 Vulcan 2.5-Inch Cat-Back

aFe
AFE49-33133
802959634660
Catback
5 Units In Stock
$ 1,585.00 $ 1,268.00
$ 1,268.00

Ford Edge Vulcan cat-back details

aFe 49-33133 Vulcan uses 2.5-inch mandrel-bent 304 stainless tubing, a resonator assembly and a black-finished high-flow stainless muffler for a mild tone. MIG-welded construction and factory-style hanger locations form the specified six-assembly system without separate decorative tips.

Key Features

  • 2.5-inch mandrel-bent 304 stainless tubing.
  • 100% MIG-welded construction.
  • ONE resonator assembly, TWO mid-pipes, LEFT/RIGHT rear tubes and ONE muffler assembly.
  • SIX 2.5-inch bands plus TWO 2.25-inch front bands.
  • Original rubber isolators retained; FOUR original hangers disengaged for removal.
  • SHORTER STRAIGHT mid-pipe ends face resonators.
  • No separate decorative tips supplied; 40-45 ft-lb bands and 50-100-mile recheck.

Fitment

Ford Edge with twin-turbo 2.7L V6: Sport 2015-2018 and ST 2019-2023. Current primary names ST 2019-2023; own March 2022 manual page 1 prints 2015-2023 with ST shorthand, while page 2 explicitly names Sport/ST but ends 2022. Exact selected live retailer table supplies Sport 2015-2018 and ST 2019-2023, reconciling grade/year scope. No blanket 2015 ST grade or later 2024 endpoint is invented. Confirm original dual front connections, hangers and retained bumper outlet interface. Broader retailer SE/SEL/Titanium/ST-Line and unrelated F-150 copy are not sufficient engine/routing proof.

Years Make Model Named grade; actual twin-turbo 2.7L Edge Sport/ST and matching original interfaces required
2019-2023 Ford Edge ST
2015-2018 Ford Edge Sport

Verify 49-33133 against the actual engine, flange, hangers and mounting locations and applicable emissions requirements before ordering.

Specifications

Detail Value
Brand aFe POWER
Manufacturer Part Number 49-33133
System Vulcan cat-back; SIX physical assemblies
Tubing / weld 2.5-inch mandrel-bent 304 stainless; MIG-welded
Resonator / muffler 05-245144 resonator assembly; 05-245148 black-finished high-flow muffler assembly
Mid-pipes TWO 05-245145; shorter straight ends insert into resonator outlets
Clamps SIX 2.5-inch 05-41061; TWO 2.25-inch 05-41210
Tips / gaskets No separate decorative tips or new gaskets itemized
Torque / recheck 40-45 ft-lb bands; re-tighten all clamps/hardware after 50-100 miles
Performance evidence No actual dyno or airflow chart, numeric horsepower/torque gain or measured cabin-drone result is linked for this exact selection. Manufacturer specifies a mild tone and high-flow black muffler, which do not establish a guaranteed gain or drone-free cabin.
Emissions Current manufacturer says no CARB EO required; no replacement converter supplied
UPC 802959634660
WARNING This product can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and reproductive harm. For more information go to www.P65Warnings.ca.gov.

What's Included

  • 1 x 05-245144: Resonator assembly.
  • 2 x 05-245145: Mid-pipe; SHORT straight end toward resonator.
  • 1 x 05-245146: LEFT rear tube.
  • 1 x 05-245147: RIGHT rear tube.
  • 1 x 05-245148: Muffler assembly.
  • 6 x 05-41061: 2.5-inch band clamp.
  • 2 x 05-41210: 2.25-inch band clamp.

SIX physical assemblies: ONE resonator assembly 05-245144, TWO mid-pipes 05-245145, ONE LEFT rear tube 05-245146, ONE RIGHT rear tube 05-245147 and ONE muffler assembly 05-245148. SIX 2.5-inch band clamps 05-41061 and TWO 2.25-inch band clamps 05-41210. Reuse original rubber isolators; original system removal disengages FOUR hangers. No separate decorative exhaust tips, new gasket, replacement converter, valve motor, wiring or intake filter/coupler is itemized. Mid-pipe quantity is TWO despite a single shared service number.

About aFe Power

aFe Power develops application-specific intake, filtration, exhaust, cooling, tuning, suspension, drivetrain, and truck-performance components supported by product testing and documented installation requirements.

Related Parts

FAQ

What is the 49-33133?

SIX physical assemblies: ONE resonator assembly 05-245144, TWO mid-pipes 05-245145, ONE LEFT rear tube 05-245146, ONE RIGHT rear tube 05-245147 and ONE muffler assembly 05-245148. SIX 2.5-inch band clamps 05-41061 and TWO 2.25-inch band clamps 05-41210. Reuse original rubber isolators; original system removal disengages FOUR hangers. No separate decorative exhaust tips, new gasket, replacement converter, valve motor, wiring or intake filter/coupler is itemized. Mid-pipe quantity is TWO despite a single shared service number.

Which Edge grades and years fit?

Ford Edge with twin-turbo 2.7L V6: Sport 2015-2018 and ST 2019-2023. Current primary names ST 2019-2023; own March 2022 manual page 1 prints 2015-2023 with ST shorthand, while page 2 explicitly names Sport/ST but ends 2022. Exact selected live retailer table supplies Sport 2015-2018 and ST 2019-2023, reconciling grade/year scope. No blanket 2015 ST grade or later 2024 endpoint is invented. Confirm original dual front connections, hangers and retained bumper outlet interface. Broader retailer SE/SEL/Titanium/ST-Line and unrelated F-150 copy are not sufficient engine/routing proof.

How many mid-pipes are supplied and which end faces forward?

TWO mid-pipes share service part 05-245145. Own step 9 specifies SHORTER STRAIGHT SECTION into rear outlets of resonator assembly. Do not reverse them or reduce bill quantity to one.

Which clamp sizes are used?

TWO 2.25-inch bands secure FRONT resonator connections. SIX 2.5-inch bands secure resonator-to-mid-pipe, mid-pipe-to-rear-tube and rear-tube-to-muffler joints in pairs.

Are separate decorative tips or new gaskets included?

No. Neither is itemized. The kit supplies resonator/muffler assemblies, two mid-pipes, left/right rear tubes and eight bands. Original rubber isolators are retained.

What band torque and recheck apply?

Align and tighten FRONT to REAR. Band clamps require 40-45 ft-lb. No separate original hanger fixing number is printed. Re-tighten all clamps/hardware after 50-100 miles.

Does it require cutting, wiring or valve transfer?

Current primary specifies no cutting/modifications. Own manual removes FOUR original hangers from rubber isolators and supplies no drilling, battery-disconnection, sensor wiring, valve transfer, coding or installation welding step.

What power or cabin-drone measurements are provided?

No actual dyno or airflow chart, numeric horsepower/torque gain or measured cabin-drone result is linked for this exact selection. Manufacturer specifies a mild tone and high-flow black muffler, which do not establish a guaranteed gain or drone-free cabin.

Installation Instructions

Verify aFe 49-33133.

  1. Read BOTH own March 2022 pages and all 17 steps/diagram. Inspect shipping condition, cool exhaust, wear eye/hand protection and support vehicle/exhaust independently at approved jack-stand positions. Lay out components and leave joints loose for alignment.
  2. Loosen original FRONT band clamps, disengage FOUR original hangers from rubber isolators and remove original exhaust. Retain original rubber isolators.
  3. Fit TWO supplied 2.25-inch band clamps over FRONT resonator assembly connections and slide assembly onto vehicle front exhaust. Engage resonator hangers in FRONT original rubber isolators.
  4. Fit TWO 2.5-inch bands on REAR resonator outlets and install BOTH mid-pipes. The SHORTER STRAIGHT SECTION of each mid-pipe goes INTO THE RESONATORS, as directed by step 9.
  5. Fit TWO 2.5-inch bands on muffler assembly and install RIGHT and LEFT rear tubes. Fit remaining TWO 2.5-inch bands over rear tubes, slide rear tubes onto mid-pipes and engage muffler hangers in original rubber isolators. Total supplied bands: SIX 2.5-inch plus TWO 2.25-inch.
  6. Align all sections and maintain safe clearance from wires, hoses, brake lines, body and tires. Tighten evenly FRONT to REAR. BAND CLAMPS require 40-45 FT-LB; no separate original hanger fixing torque is printed.
  7. Start engine, inspect/repair leaks and lower vehicle. Re-tighten all clamps/hardware after 50-100 miles. Current primary specifies no cutting/modifications; own manual supplies no drilling, battery-disconnection, sensor wiring, valve transfer, coding or installation welding step. No decorative tip installation step is supplied.

No actual dyno or airflow chart, numeric horsepower/torque gain or measured cabin-drone result is linked for this exact selection. Manufacturer specifies a mild tone and high-flow black muffler, which do not establish a guaranteed gain or drone-free cabin. Manual pages carry different grade/year headers; current exact ST primary and exact selected Sport/ST retailer rows qualify the scope. No 2015 ST, 2024 extension, unrelated F-150 or broader 2.0L trim application is inferred.

California Proposition 65 warning: this product can expose you to chemicals known to the State of California to cause cancer and reproductive harm.

aFe

aFe

Shop aFe POWER intake systems, replacement filters, exhaust components, BladeRunner cooling parts and CONTROL chassis accessories at Black Ops Auto Works. Compare Momentum GT, Track Series and Magnum FORCE intake applications alongside Pro DRY S and Pro 5R filter choices. Choose a complete upgrade or a service component for the system already on your car, truck or SUV.Choose Your aFe Intake and FilterMomentum GT, Track Series and Magnum FORCECompare the intake housing, tubing, filter arrangement and finish offered for your engine. The collection includes Momentum GT applications, selected carbon-fiber Track Series systems and Magnum FORCE configurations. Each package supplies its own combination of induction components, so choose the design for the installation you want.Pro DRY S or Pro 5R Filter MediaPro DRY S uses oil-free media and skips the re-oiling step during service. Pro 5R is an oiled filter option with a different maintenance procedure. Choose a media configuration aFe off...

View aFe Products
Catback

Catback

Shop cat-back exhaust systems for a more distinctive voice and a coordinated rear-end finish at Black Ops Auto Works. Compare Borla S-Type and ATAK, CORSA Sport and Xtreme, AWE Touring and Track, MBRP and other listed systems for the exact vehicle. Choose the sound character you want at acceleration and cruise, then compare material, valve operation, exit layout and tips.Borla and CORSA Sound ChoicesBorla S-Type and ATAK provide different sound characters, with ATAK the more aggressive option where both are offered. Compare manufacturer sound clips on the same engine and vehicle, including the installed headers or other front-exhaust changes that affect the finished note.CORSA Sport and Xtreme likewise have different sound levels. Its RSC technology targets unwanted cruising resonance in the designed system. Choose the actual application and sound family rather than assuming the loudest acceleration note must also mean the most cabin drone.AWE Touring, Track and Other Product Famili...

View Catback Products
Exhaust Systems

Exhaust Systems

Shop performance exhaust systems, cat-backs, axle-backs, headers, mufflers, and exhaust tips at Black Ops Auto Works. Compare options from Borla, CORSA, Solo Performance, AWE, MagnaFlow, MBRP, Kooks, Akrapovic, Invidia, and other brands. Find complete systems and individual components for muscle cars, performance SUVs, trucks, imports, and European vehicles. Cat-Back and Axle-Back Exhaust Systems Choose the exhaust section that matches your project. Cat-back systems generally replace the exhaust downstream of the catalytic converter, while axle-back systems replace the rear section. Exact connection points and package contents vary by vehicle. Compare muffler design, pipe diameter, exit location, tip configuration, and compatibility with existing exhaust components. Exhaust for HEMI, SRT, Trackhawk, and Hellcat Vehicles This collection includes exhaust options for selected Jeep Grand Cherokee SRT and Trackhawk, Dodge Durango SRT and Hellcat, Dodge Charger, Chrysler 300, and Ram appl...

View Exhaust Systems Products
Ford Edge Parts and Accessories

Ford Edge Parts and Accessories

Shop Ford Edge brake, suspension, intake and accessory references at Black Ops Auto Works. Compare aFe Momentum GT filter options, Thermal R&D Edge ST exhaust, Bilstein or KYB suspension service and Husky floor or body protection. Match actual year, engine and trim, with Sport and ST applications checked separately.aFe Intake and Edge ST Exhaust ChoicesaFe Momentum GT titles offer Pro DRY S and Pro 5R filter configurations. Confirm exact engine and intake part number, then compare filter-care requirements and supplied installation components. Thermal R&D titles distinguish a 2019–2024 Edge ST cat-back system from separate polished tips. J&L oil-separator coverage names Edge Sport/ST applications. Match complete engine, side, mounting and connections before combining parts in a build plan.Bilstein and KYB Suspension ServiceBilstein B4 and B6 titles provide separate shock or strut references with stated positions and production ranges. A KYB rear Gas-A-Just title names SE,...

View Ford Edge Parts and Accessories Products
Military & First Responder Discounts

Military & First Responder Discount Program

Black Ops Auto Works proudly honors active duty military, veterans, National Guard, reserves, police officers, firefighters, and EMTs with an exclusive 5% discount on all performance parts and carbon fiber upgrades. Verify instantly and start saving today.

Learn More & Apply

Your cart

×