-20%
Click to zoom in
Ford Ranger Apollo GT muffler-delete axle-back
The aFe 49-43114-B is a 3-inch mandrel-bent 409 stainless, MIG-welded muffler-delete axle-back with one black 4.5-inch-outlet stainless tip and passenger-side exit. It replaces the factory rear muffler assembly; no new muffler is included. Selected coverage is 2019-2023 Ranger gas 2.3L EcoBoost. SuperCrew, 5-foot/61-inch bed and 126.8-inch wheelbase ONLY. No SuperCab, later generation, Raptor or other engine approval is inferred.
Key Features
- Selected aFe part 49-43114-B.
- 3-inch mandrel-bent 409 stainless tubing with MIG-welded construction.
- Factory rear muffler deleted; no replacement muffler included.
- One 4.5-inch black stainless outlet tip; grade/dimension wording qualified below.
- Factory mounting locations with the selected guide's hardware and cab-specific requirements.
Fitment
2019-2023 Ranger gas 2.3L EcoBoost. SuperCrew, 5-foot/61-inch bed and 126.8-inch wheelbase ONLY. No SuperCab, later generation, Raptor or other engine approval is inferred. The full exact-part named table supplies the actual named rows below. No Raptor-R, diesel, later-generation or other-engine fit is inferred.
| Years | Make | Model | Submodel | Cab/bed and equipment limits |
|---|---|---|---|---|
| 2019-2023 | Ford | Ranger | Lariat | SuperCrew, 5-foot/61-inch bed and 126.8-inch wheelbase ONLY. No SuperCab, later generation, Raptor or other engine approval is inferred. |
| 2019-2023 | Ford | Ranger | XL | SuperCrew, 5-foot/61-inch bed and 126.8-inch wheelbase ONLY. No SuperCab, later generation, Raptor or other engine approval is inferred. |
| 2019-2023 | Ford | Ranger | XLT | SuperCrew, 5-foot/61-inch bed and 126.8-inch wheelbase ONLY. No SuperCab, later generation, Raptor or other engine approval is inferred. |
Specifications
| Detail | Value |
|---|---|
| Manufacturer Part Number | 49-43114-B |
| Product type | Axle Back |
| Construction | 3-inch mandrel-bent 409 stainless, MIG welded. |
| Selected bill | one over-axle assembly 05-144709, one tailpipe assembly 05-144710, one 2.5-inch band 05-41061, one 3-inch band 05-41055 and one selected black tip 49T30451-B09. The polished alternative is not an additional tip; no muffler is included. |
| Cab and equipment scope | SuperCrew, 5-foot/61-inch bed and 126.8-inch wheelbase ONLY. No SuperCab, later generation, Raptor or other engine approval is inferred. |
| Guide clarification | The current primary describes a 4.5-inch-diameter stainless outlet tip, while the bill and step 8 label the selected tip 3-inch and the bill calls it 409SS. Do not silently treat those dimensions as the same measurement or promise 304 alloy from a part-number prefix. Confirm actual inlet/outlet and replacement-tip specification with aFe if required; the listing retains the primary 4.5-inch outlet description and general stainless tip material. |
| Configuration-dependent installation | No extension or cutting procedure is specified. Remove the factory muffler at its front clamped joint; install the over-axle assembly using the 2.5-inch band and original isolation mount, then tailpipe/tip using the 3-inch band and original mount. |
| Tightening and recheck | The guide specifies band-clamp torque of 40-45 ft-lb only; no separate tip-fastener setting is printed. Align all sections with safe clearance from wires, hoses, brake lines, body parts and tires; no fixed dimension is printed. Tighten front to rear, check for leaks, lower the vehicle and retighten all clamps and hardware after 50-100 miles. |
| Sound and performance | The primary describes an aggressive sound and muffler-delete configuration but provides no selected measured power or flow chart. No guaranteed gain or drone-free result is established. |
| Emissions statement | The manufacturer says no CARB EO is required for this product. This does not approve unrelated exhaust modifications. |
What's Included
- The 49-43114-B kit includes one over-axle assembly 05-144709, one tailpipe assembly 05-144710, one 2.5-inch band 05-41061, one 3-inch band 05-41055 and one selected black tip 49T30451-B09. The polished alternative is not an additional tip; no muffler is included.
- The current primary describes a 4.5-inch-diameter stainless outlet tip, while the bill and step 8 label the selected tip 3-inch and the bill calls it 409SS. Do not silently treat those dimensions as the same measurement or promise 304 alloy from a part-number prefix. Confirm actual inlet/outlet and replacement-tip specification with aFe if required; the listing retains the primary 4.5-inch outlet description and general stainless tip material.
About aFe Power
aFe Power develops application-specific intake, filtration, exhaust, cooling, tuning, suspension, drivetrain, and truck-performance components supported by product testing and documented installation requirements.
Related Parts
- Exact selected manufacturer application and construction
- Complete selected guide, bill and cab-dependent procedure
- Full exact-part named fitment table
- Compare axle-back systems
FAQ
What is the 49-43114-B?It is a 3-inch mandrel-bent 409 stainless, MIG-welded muffler-delete axle-back with one black 4.5-inch-outlet stainless tip and passenger-side exit. It replaces the factory rear muffler assembly; no new muffler is included. Match 2019-2023 Ranger gas 2.3L EcoBoost.
Which cab, bed and wheelbase restrictions apply?SuperCrew, 5-foot/61-inch bed and 126.8-inch wheelbase ONLY. No SuperCab, later generation, Raptor or other engine approval is inferred.
What parts are included with the selected finish?one over-axle assembly 05-144709, one tailpipe assembly 05-144710, one 2.5-inch band 05-41061, one 3-inch band 05-41055 and one selected black tip 49T30451-B09. The polished alternative is not an additional tip; no muffler is included.
Which hardware or specification detail needs confirmation?The current primary describes a 4.5-inch-diameter stainless outlet tip, while the bill and step 8 label the selected tip 3-inch and the bill calls it 409SS. Do not silently treat those dimensions as the same measurement or promise 304 alloy from a part-number prefix. Confirm actual inlet/outlet and replacement-tip specification with aFe if required; the listing retains the primary 4.5-inch outlet description and general stainless tip material.
How do extensions and original mounts apply?No extension or cutting procedure is specified. Remove the factory muffler at its front clamped joint; install the over-axle assembly using the 2.5-inch band and original isolation mount, then tailpipe/tip using the 3-inch band and original mount.
What tightening and follow-up checks apply?The guide specifies band-clamp torque of 40-45 ft-lb only; no separate tip-fastener setting is printed. Align all sections with safe clearance from wires, hoses, brake lines, body parts and tires; no fixed dimension is printed. Tighten front to rear, check for leaks, lower the vehicle and retighten all clamps and hardware after 50-100 miles.
Is cutting required?The selected primary states no cutting is required.
Are gains or drone-free operation guaranteed?The primary describes an aggressive sound and muffler-delete configuration but provides no selected measured power or flow chart. No guaranteed gain or drone-free result is established.
Installation Instructions
- Confirm aFe 49-43114-B against the exact vehicle and installed equipment. Inventory the actual components and follow the selected manufacturer instructions and current vehicle service requirements.
- Match the exact selected vehicle, engine, actual cab/bed and wheelbase. SuperCrew, 5-foot/61-inch bed and 126.8-inch wheelbase ONLY. No SuperCab, later generation, Raptor or other engine approval is inferred. Read the complete selected instructions, inspect actual packing and resolve the hardware/specification gaps before disassembly. Allow the system to cool; support the vehicle safely and independently support the exhaust. Leave joints loose until all components are installed.
- Remove the original muffler at its front clamped joint. Retain original rubber isolation mounts. Install the selected over-axle assembly with the supplied 2.5-inch band and original mount, then the selected tailpipe and black tip using the 3-inch band and original mount. Adjust tip position.
- The guide specifies band-clamp torque of 40-45 ft-lb only; no separate tip-fastener setting is printed. Align all sections with safe clearance from wires, hoses, brake lines, body parts and tires; no fixed dimension is printed. Tighten front to rear, check for leaks, lower the vehicle and retighten all clamps and hardware after 50-100 miles. No battery, sensor, ground-strap, crossmember or related-system procedure is borrowed. The current primary describes a 4.5-inch-diameter stainless outlet tip, while the bill and step 8 label the selected tip 3-inch and the bill calls it 409SS. Do not silently treat those dimensions as the same measurement or promise 304 alloy from a part-number prefix. Confirm actual inlet/outlet and replacement-tip specification with aFe if required; the listing retains the primary 4.5-inch outlet description and general stainless tip material.
California Proposition 65 warning: this product can expose you to chemicals known to the State of California to cause cancer and reproductive harm.
aFe
Shop aFe POWER intake systems, replacement filters, exhaust components, BladeRunner cooling parts and CONTROL chassis accessories at Black Ops Auto Works. Compare Momentum GT, Track Series and Magnum FORCE intake applications alongside Pro DRY S and Pro 5R filter choices. Choose a complete upgrade or a service component for the system already on your car, truck or SUV.Choose Your aFe Intake and FilterMomentum GT, Track Series and Magnum FORCECompare the intake housing, tubing, filter arrangement and finish offered for your engine. The collection includes Momentum GT applications, selected carbon-fiber Track Series systems and Magnum FORCE configurations. Each package supplies its own combination of induction components, so choose the design for the installation you want.Pro DRY S or Pro 5R Filter MediaPro DRY S uses oil-free media and skips the re-oiling step during service. Pro 5R is an oiled filter option with a different maintenance procedure. Choose a media configuration aFe off...
View aFe Products
Axle Back
Shop axle-back exhaust systems and rear exhaust sections at Black Ops Auto Works. Compare Borla, CORSA, AWE, MBRP, MagnaFlow, Dinan and other listed options for a change in exhaust character and rear-end appearance. Choose the sound level, valve arrangement and tip design that suit your vehicle and the rest of its exhaust.Choose the Rear Section for Your ProjectAn axle-back normally focuses the change on the rear exhaust section, while a cat-back replaces a broader portion of the system. Use the exact kit’s connection points and contents to understand what stays on the vehicle and what changes. Factory routing and aftermarket terminology vary by application.For an existing modified exhaust, include the current mid-pipe, resonators and other changes when comparing sound clips and installation requirements. The rear section is one part of the complete sound you will hear.Compare Sound Character and Cruising ComfortBorla offers different sound levels such as S-Type and ATAK where avail...
View Axle Back Products
Exhaust Systems
Shop performance exhaust systems, cat-backs, axle-backs, headers, mufflers, and exhaust tips at Black Ops Auto Works. Compare options from Borla, CORSA, Solo Performance, AWE, MagnaFlow, MBRP, Kooks, Akrapovic, Invidia, and other brands. Find complete systems and individual components for muscle cars, performance SUVs, trucks, imports, and European vehicles. Cat-Back and Axle-Back Exhaust Systems Choose the exhaust section that matches your project. Cat-back systems generally replace the exhaust downstream of the catalytic converter, while axle-back systems replace the rear section. Exact connection points and package contents vary by vehicle. Compare muffler design, pipe diameter, exit location, tip configuration, and compatibility with existing exhaust components. Exhaust for HEMI, SRT, Trackhawk, and Hellcat Vehicles This collection includes exhaust options for selected Jeep Grand Cherokee SRT and Trackhawk, Dodge Durango SRT and Hellcat, Dodge Charger, Chrysler 300, and Ram appl...
View Exhaust Systems Products
Ford Ranger Parts and Accessories
Shop Ford Ranger parts for bed protection, easier access, suspension projects and brake or engine service at Black Ops Auto Works. Compare BAK covers, AMP Research steps, Bilstein suspension references and Husky protection around the truck you drive. Match exact generation, cab, bed, powertrain and drivetrain before ordering.Bed Covers, Caps and Access StepsBAK references distinguish MX4 folding and Revolver X4s roll-up choices for stated bed applications. Match exact bed dimensions, rails and accessory compatibility. The Westin EXP cap Box 1 title explicitly requires Box 2; review the complete package before planning installation. AMP PowerStep, RealTruck bars and other steps need exact cab and production coverage, while rack-frame-only titles require separate hardware.Suspension and Wheel PlanningBilstein references distinguish newer Ranger 6112 front leveling, 6100 rear and 5100 options from earlier chassis applications. Eibach 2WD, Superlift 4WD and MaxTrac references address di...
View Ford Ranger Parts and Accessories Products