aFe Control 05-23 Toyota Tacoma Upper Control Arms - Red Anodized Billet Aluminum

Precision-Built Billet Aluminum Upper Control Arm Upgrade for the 2022-2023 Toyota Tundra

The aFe Control upper control arm kit 460-72T005-R delivers extended travel and improved alignment geometry that stock arms cannot achieve, especially critical with lift kits and leveling spacers for the 2022-2023 Toyota Tundra. Built from billet aluminum and engineered to OEM or better fitment standards, the 460-72T005-R installs using factory mounting points with no cutting, welding, or permanent modification to the chassis. Every component is precision-machined and tested to withstand the thermal and mechanical loads of both daily commuting and performance driving, giving you a measurable improvement in handling character the moment you leave the driveway.

Key Features

• Material: billet aluminum construction for strength and corrosion resistance
• Finish: red anodized for long-term durability
• Direct bolt-on using factory mounting points, no chassis modification required
• Precision-machined for consistent, repeatable fitment
• Improved handling balance, reduced body roll, and enhanced driver feel
• Compatible with factory wheel and tire sizes (verify clearance for larger setups)
• Backed by aFe Power limited manufacturer warranty

Fitment

Specifications

What's Included

• aFe Control upper control arm kit (460-72T005-R)
• All required mounting hardware
• Installation instructions

Frequently Asked Questions

Yes. Any suspension component that affects wheel geometry, including control arms, lowering springs, coilovers, and lift kits, requires a four-wheel alignment after installation. Driving on a significantly out-of-alignment vehicle accelerates tire wear and compromises handling safety.

In most cases, yes. However, with stacked suspension modifications, always verify component clearances and maximum travel ranges. If you are running a combination of lift, aftermarket wheels, and larger tires, consult an alignment specialist familiar with your platform before finalizing the build.

Yes. Under the Magnuson-Moss Warranty Act, a dealer cannot void your vehicle warranty solely because you installed aftermarket suspension components. They must demonstrate a direct causal link between the suspension modification and any specific failure they are declining to cover.

Installation time varies by component type. A strut brace or sway bar end link set can be completed in one to two hours. A full coilover or control arm replacement typically takes four to six hours in a properly equipped shop. Always factor in time for a post-installation alignment.

Many of these components can be installed at home with standard hand tools and a floor jack and jack stands. Coilovers and control arms require spring compressors or a press for certain steps and benefit from a shop alignment lift. Evaluate your specific toolkit and comfort level before committing to a DIY install.

Performance suspension upgrades are designed to improve handling precision. Sway bars, control arms, and strut braces stiffen lateral dynamics while leaving ride compliance largely intact. Coilovers and lowering springs will reduce ride height and typically firm the ride relative to factory. The trade-off between sport handling and daily comfort varies by product selection.

aFe Power provides a limited manufacturer warranty on all suspension products covering defects in materials and workmanship. Coverage does not include damage from improper installation, racing use, off-road impacts, or modification of the components. Contact aFe Power or us for full warranty details.

Refer to the fitment table above for confirmed compatible year ranges and trim levels. If your specific configuration is not listed, contact us before purchasing. We can verify fitment details with aFe Power to ensure the correct part is ordered.

Installation Overview

1. Safely raise and support the vehicle on a level surface using proper jack stands under the frame
2. Remove the wheel for full access to the suspension mounting points if required by your specific component
3. Take photographs of the factory orientation for all mounting hardware positions before disassembly
4. Remove factory components in the reverse order of installation, keeping hardware organized
5. Install the new 460-72T005-R in the factory mounting positions, hand-threading all hardware first
6. Confirm all components are properly seated and aligned before final torquing
7. Torque all hardware to specification in the correct sequence as specified in the instructions
8. Reinstall the wheel, lower the vehicle, and perform a visual inspection before driving
9. Schedule a four-wheel alignment at a qualified shop before regular driving

WARNING: This product can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and reproductive harm. For more information go to www.P65Warnings.ca.gov.