-20%
Click to zoom in
Replacement intake coupling kit
aFe 59-00036 supplies the specified silicone with a layer of polyester reinforcement; exact total ply count not stated connection and listed clamp hardware. Match the actual installed assembly before ordering.
Key Features
- Heading: 4.15 x 3-1/2 in ID and 3-1/2 in length. Details: 4-3/16 x 3-1/2 in ID, 3 in length, 49-degree angle. Verify actual revision.
- Silicone with a layer of polyester reinforcement; exact total ply count not stated.
- Exact kit contents are listed below; this component kit is not a complete intake.
Fitment
| Application | Required checks |
|---|---|
| Specification-matched intake connection | Match the actual elbow-reducer connection, angle and clearance before ordering. The current manufacturer heading gives 4.15-inch x 3-1/2-inch internal diameters and 3-1/2-inch length, while its detailed description gives 4-3/16-inch x 3-1/2-inch diameters, 3-inch length and a 49-degree angle. The kit list again prints 4.15 x 3.5-inch ID. These nominal/revision figures are unresolved; confirm the actual supplied coupling rather than assuming all dimensions are interchangeable. |
Specifications
| Brand | aFe POWER |
|---|---|
| Manufacturer Part Number | 59-00036 |
| Product | Replacement intake coupling kit |
| Geometry | Heading: 4.15 x 3-1/2 in ID and 3-1/2 in length. Details: 4-3/16 x 3-1/2 in ID, 3 in length, 49-degree angle. Verify actual revision. |
| Construction | Silicone with a layer of polyester reinforcement; exact total ply count not stated |
| Pressure / temperature rating | No numeric operating rating supplied by this exact page |
| Tightening torque | No numeric clamp torque supplied by this exact page |
| Emissions statement | Manufacturer states this service component does not require a CARB EO number. Complete intake compliance remains separate. |
| UPC | 802959593202 |
| WARNING | This product can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and reproductive harm. For more information go to www.P65Warnings.ca.gov. |
What's Included
One reinforced silicone elbow coupling and two stainless-steel worm clamps: one #072 and one #060. No tube, filter or complete intake is itemized.
| Manufacturer service part | Listed component |
|---|---|
| 05-01353 | Elbow coupling listed as 4.15 x 3.5 in ID, 49 degrees; detailed dimensions conflict as qualified |
| 03-50010 | Stainless-steel #072 worm clamp |
| 03-50002 | Stainless-steel #060 worm clamp |
The generic manufacturer Filter Included field does not itemize a separate air filter in this coupling kit.
About aFe Power
aFe Power develops application-specific intake, filtration, exhaust, cooling, tuning, suspension, drivetrain, and truck-performance components supported by product testing and documented installation requirements.
Related Parts
Frequently Asked Questions
Which connection does this coupling require?Match the actual elbow-reducer connection, angle and clearance before ordering. The current manufacturer heading gives 4.15-inch x 3-1/2-inch internal diameters and 3-1/2-inch length, while its detailed description gives 4-3/16-inch x 3-1/2-inch diameters, 3-inch length and a 49-degree angle. The kit list again prints 4.15 x 3.5-inch ID. These nominal/revision figures are unresolved; confirm the actual supplied coupling rather than assuming all dimensions are interchangeable.
What material is specified?Silicone with a layer of polyester reinforcement; exact total ply count not stated. Do not select a replacement by assuming every flexible intake coupling uses the same material.
What dimensions and geometry should I check?Heading: 4.15 x 3-1/2 in ID and 3-1/2 in length. Details: 4-3/16 x 3-1/2 in ID, 3 in length, 49-degree angle. Verify actual revision. Match full tube engagement and clearance as well as nominal diameter.
Which hardware is supplied?One reinforced silicone elbow coupling and two stainless-steel worm clamps: one #072 and one #060. No tube, filter or complete intake is itemized.
Are numeric pressure or temperature ratings supplied?The exact current page does not provide numeric operating pressure or temperature ratings. Its general engine-compartment or flexibility description does not certify suitability for every pressurized or fluid-system use.
What clamp torque should I use?No numeric clamp torque is stated on this exact page. Follow the applicable installed intake and connection instructions rather than borrowing a torque from unrelated clamps.
Which dimensions should resolve the conflicting heading and details?The exact page contains both 4.15 and 4-3/16-inch large-end figures and both 3-1/2 and 3-inch lengths. The details identify a 49-degree angle. The page alone does not resolve the actual revision; verify the supplied part against the installed connection.
Does this kit replace the complete intake?No. The kit contents are the coupling and listed hardware. A complete intake, housing, air filter, sensor or calibration is not supplied unless specifically itemized; this listing does not certify vehicle power gains.
Installation Instructions
Confirm aFe 59-00036 and the actual installed intake connection. Compare all diameters, length, shape, seal engagement and clearance before fitting the coupling and listed clamps. Follow that assembly’s instructions for placement, tightening and checks. This exact kit page does not supply a numeric clamp torque or complete vehicle-specific intake procedure.
Important Disclosures
California Proposition 65 warning: this product can expose you to chemicals known to the State of California to cause cancer and reproductive harm.
aFe
Shop aFe POWER intake systems, replacement filters, exhaust components, BladeRunner cooling parts and CONTROL chassis accessories at Black Ops Auto Works. Compare Momentum GT, Track Series and Magnum FORCE intake applications alongside Pro DRY S and Pro 5R filter choices. Choose a complete upgrade or a service component for the system already on your car, truck or SUV.Choose Your aFe Intake and FilterMomentum GT, Track Series and Magnum FORCECompare the intake housing, tubing, filter arrangement and finish offered for your engine. The collection includes Momentum GT applications, selected carbon-fiber Track Series systems and Magnum FORCE configurations. Each package supplies its own combination of induction components, so choose the design for the installation you want.Pro DRY S or Pro 5R Filter MediaPro DRY S uses oil-free media and skips the re-oiling step during service. Pro 5R is an oiled filter option with a different maintenance procedure. Choose a media configuration aFe off...
View aFe Products
Air Intake Systems
Shop performance air intake systems for your next engine-bay upgrade at Black Ops Auto Works. Compare complete cold-air intakes, short-ram layouts and enclosed systems from Legmaker, JLT, aFe, K&N, Injen and other listed manufacturers. Choose the intake character, packaging and filter-service approach that suit the vehicle and the way you use it.Complete Intakes or a Focused Component UpgradeA complete intake is the place to start when changing the filter, tubing and enclosure as a matched package. An individual airbox, intake tube, coupler or replacement filter can be a better purchase when the rest of the installed system is staying. Compare what the package supplies before choosing between the two routes.For a naturally aspirated, turbocharged or supercharged engine, the connection and sensor arrangement are part of the design. Choose the complete system for that application rather than combining a large tube and filter solely by appearance.Cold-Air, Short-Ram and Enclosed De...
View Air Intake Systems Products
Silicone Couplers & Hoses
Shop silicone couplers, formed hoses and selected connection components at Black Ops Auto Works. Compare Vibrant, Mishimoto, do88, BMC, Ticon, Turbosmart and other listed references for intake, charge-air, vacuum and specifically supported fluid circuits. Choose service duty and geometry before color or brand.Straight, Reducer and Elbow GeometryStraight and reducing couplers, angled elbows, hump and T-hose layouts make different connections. Match both end inside diameters, leg/overall lengths, bend and branch dimensions to the actual pipes.Clamp range is based on the installed hose outside diameter and interface, not simply the nominal bore. Compare wall thickness, pipe engagement and bead/retention requirements using the exact hose and clamp instructions.Formed Vehicle Hoses and Hardwaredo88 references distinguish turbo inlets, pressure/intercooler hoses, crankvent/solenoid sections and exact engine/turbo arrangements. Some Saab listings vary with battery size; Audi RS3/TT RS refe...
View Silicone Couplers & Hoses Products