aFe 54-76012-S This black molded LLDPE scoop channels air from the front grille into a compatible Momentum airbox. Its separate hump coupling uses two different clamp sizes and the installation reuses five original radiator-support panel clips.
Toyota Tacoma V6-4.0L with the required Momentum housing. The current exact manufacturer page and manual cover the broader 2005-2015 family and name Momentum 51/54/75-76004 and 51/54/75-76012 as the compatible parents. Exact-part named-trim retailer tables retain the 2012-2015 rows below; earlier named-trim additions remain unverified rather than being inferred from the family headline. This accessory does not establish compatibility with an original Toyota airbox or a different intake housing.
| Years | Make | Model | Named trim; actual engine and hood requirements apply |
|---|---|---|---|
| 2012-2013 | Toyota | Tacoma | X-Runner |
| 2012-2015 | Toyota | Tacoma | Base |
| 2012-2015 | Toyota | Tacoma | Pre Runner |
| 2015 | Toyota | Tacoma | TRD Pro |
Verify 54-76012-S against the actual engine, sensor and vent connections, mounting locations and applicable emissions requirements before ordering.
| Brand | aFe POWER |
| Manufacturer Part Number | 54-76012-S |
| Family coverage | Tacoma V6-4.0L 2005-2015 in current primary/manual; earlier named rows require confirmation |
| Compatible parents | Momentum 51/54/75-76004 and 51/54/75-76012 |
| Scoop material | Current manufacturer LLDPE; older retailer XLPE description differs |
| Coupling / clamps | 05-01386 / #052 03-50008 and #060 03-50002 |
| Original clips | Nine removed; five reused |
| Recheck / torque | 100-200 miles / no numeric torque specified |
| Emissions | The current exact manufacturer pages and manuals state that this product is not currently CARB exempt and is unavailable for purchase in California or use on a vehicle registered with the California DMV. A fitment statement for a supercharger does not establish emissions approval. |
| Quantity | Manufacturer service part | Component |
|---|---|---|
| 1 | 05-76012B3 | Black rotomolded scoop |
| 1 | 05-01386 | Silicone hump coupling |
| 1 | 03-50008 | #052 clamp |
| 1 | 03-50002 | #060 clamp |
The exact BOM lists ONE black scoop 05-76012B3, ONE 05-01386 silicone hump coupling, ONE #052 clamp 03-50008 and ONE #060 clamp 03-50002. Reuse five of the nine original support-panel clips; no new clip set, filter, intake tube or sensor is listed. The current manufacturer specifies LLDPE, while older retailer copy calls it XLPE; LLDPE is the current primary-source description.
aFe Power develops application-specific intake, filtration, exhaust, cooling, tuning, suspension, drivetrain, and truck-performance components supported by product testing and documented installation requirements.
Toyota Tacoma V6-4.0L with the required Momentum housing. The current exact manufacturer page and manual cover the broader 2005-2015 family and name Momentum 51/54/75-76004 and 51/54/75-76012 as the compatible parents. Exact-part named-trim retailer tables retain the 2012-2015 rows below; earlier named-trim additions remain unverified rather than being inferred from the family headline. This accessory does not establish compatibility with an original Toyota airbox or a different intake housing.
What exactly is supplied?The exact BOM lists ONE black scoop 05-76012B3, ONE 05-01386 silicone hump coupling, ONE #052 clamp 03-50008 and ONE #060 clamp 03-50002. Reuse five of the nine original support-panel clips; no new clip set, filter, intake tube or sensor is listed. The current manufacturer specifies LLDPE, while older retailer copy calls it XLPE; LLDPE is the current primary-source description.
Is this a filter or complete intake?No. It directs front-grille air into the specified Momentum housing through its own coupling. No air filter, MAF or complete intake assembly is listed in this accessory BOM.
How many original clips are reused?Remove nine original radiator-support-cover panel clips carefully and retain five. Align the scoop with its five mounting holes and reuse those five clips. Do not borrow the three-of-seven clip procedure from the later 3.5L kit.
Which coupling clamp goes where?The #060 clamp secures hump coupling 05-01386 at the airbox. Place the #052 clamp over the coupling before sliding the scoop outlet into it, then verify full seating on both sides before tightening.
Does this require cutting or drilling?The exact instructions use existing panel-clip locations and do not prescribe cutting or drilling. Match the required parent airbox and actual factory support arrangement.
Does the scoop have an independent power or fording rating?No separate scoop-only flow/dyno result or water-fording depth is established by this exact page or manual. Complete-intake test figures are not independent scoop gains.
What recheck and emissions limits apply?Recheck clamps and connectors after 100-200 miles; no numeric torque is given. The current exact manufacturer pages and manuals state that this product is not currently CARB exempt and is unavailable for purchase in California or use on a vehicle registered with the California DMV. A fitment statement for a supercharger does not establish emissions approval.
Verify aFe 54-76012-S. Remove NINE original radiator-support cover panel clips by releasing the center pins and remove the cover; retain FIVE clips for reuse. Fit supplied hump coupling 05-01386 to the correct Momentum airbox using the larger #060 clamp. Put the #052 clamp over the coupling before aligning the scoop with the five radiator-support mounting holes and sliding its outlet into the coupling. Secure the scoop using the five retained clips. Check full coupling seating around BOTH the airbox and scoop, then secure both clamps with the specified 8mm nut driver. Recheck clamps and connectors after 100-200 miles; no numeric torque is specified.
Toyota Tacoma V6-4.0L with the required Momentum housing. The current exact manufacturer page and manual cover the broader 2005-2015 family and name Momentum 51/54/75-76004 and 51/54/75-76012 as the compatible parents. Exact-part named-trim retailer tables retain the 2012-2015 rows below; earlier named-trim additions remain unverified rather than being inferred from the family headline. This accessory does not establish compatibility with an original Toyota airbox or a different intake housing. The current exact manufacturer pages and manuals state that this product is not currently CARB exempt and is unavailable for purchase in California or use on a vehicle registered with the California DMV. A fitment statement for a supercharger does not establish emissions approval.
California Proposition 65 warning: this product can expose you to chemicals known to the State of California to cause cancer and reproductive harm.
Shop aFe POWER intake systems, replacement filters, exhaust components, BladeRunner cooling parts and CONTROL chassis accessories at Black Ops Auto Works. Compare Momentum GT, Track Series and Magnum FORCE intake applications alongside Pro DRY S and Pro 5R filter choices. Choose a complete upgrade or a service component for the system already on your car, truck or SUV.Choose Your aFe Intake and FilterMomentum GT, Track Series and Magnum FORCECompare the intake housing, tubing, filter arrangement and finish offered for your engine. The collection includes Momentum GT applications, selected carbon-fiber Track Series systems and Magnum FORCE configurations. Each package supplies its own combination of induction components, so choose the design for the installation you want.Pro DRY S or Pro 5R Filter MediaPro DRY S uses oil-free media and skips the re-oiling step during service. Pro 5R is an oiled filter option with a different maintenance procedure. Choose a media configuration aFe off...
View aFe Products
Shop performance air intake systems for your next engine-bay upgrade at Black Ops Auto Works. Compare complete cold-air intakes, short-ram layouts and enclosed systems from Legmaker, JLT, aFe, K&N, Injen and other listed manufacturers. Choose the intake character, packaging and filter-service approach that suit the vehicle and the way you use it.Complete Intakes or a Focused Component UpgradeA complete intake is the place to start when changing the filter, tubing and enclosure as a matched package. An individual airbox, intake tube, coupler or replacement filter can be a better purchase when the rest of the installed system is staying. Compare what the package supplies before choosing between the two routes.For a naturally aspirated, turbocharged or supercharged engine, the connection and sensor arrangement are part of the design. Choose the complete system for that application rather than combining a large tube and filter solely by appearance.Cold-Air, Short-Ram and Enclosed De...
View Air Intake Systems Products
Shop elevated intake snorkels, air scoops and ducting at Black Ops Auto Works. Compare ARB Safari, K&N elevated intakes and aFe D.A.S. snorkels for supported off-road applications, plus aFe dynamic scoops, HKS ducts/boxes and the Black Ops Huracan STO roof-scoop inlet. Choose the actual air-routing job before comparing materials and appearance.Elevated Intake SnorkelsARB Safari Rspec, Vspec and Armax references target named engine/chassis combinations. K&N elevated intake kits also distinguish Tacoma, 4Runner and Bronco applications. Compare required connections, intake-box compatibility and bodywork with the exact kit.aFe lists a separate Gladiator Mojave 3.6L D.A.S. snorkel from its other JL/JT configuration. Match the actual trim and induction layout rather than assuming all Gladiator snorkels use the same installation.Dynamic Scoops and Air CatchersaFe Challenger Air Catcher references include polyethylene color choices and a carbon-fiber version. Other dynamic scoops na...
View Scoops & Snorkels Products
Shop Toyota Tacoma parts for suspension projects, body protection, bed access and everyday maintenance at Black Ops Auto Works. Explore Fox, ICON and Old Man Emu references, bumper components, bed covers and cab-specific steps. Coordinate the complete order around your generation, powertrain, drivetrain, cab and bed.Suspension Across Tacoma GenerationsFox, Bilstein, ICON and OME references span different generations, axle positions and staged configurations. Match factory suspension, drivetrain and current ride height before comparing individual dampers, coilovers or complete systems. Extended-travel and load-specific references require their full supporting setup and installation plan reviewed.Body Protection, Steps and Bed EquipmentBumper, skid, recovery-point and running-board references serve different mounting positions and cab types. Bed toppers, covers and rack frames require exact bed and rail coverage. A topper listed as Box 1 with Box 2 required, or a rack frame requiring ...
View Toyota Tacoma Parts and Accessories Products
