aFe 54-72104 Momentum GT intake uses one reinforced Pro 5R oiled filter, molded XLPE housing and tube for 2017-2018 Ram 2500/3500 6.4L HEMI configurations without a mass-airflow sensor, including Power Wagon. The original air duct, temperature sensor and CCV connection are retained, while the AC-line isolation mount reattaches using supplied M6 hardware.
Current exact manufacturer page and twenty-page manual identify Ram 2500/3500 and 2500 Power Wagon 2017-2018 with 6.4L HEMI and no MAF. This includes qualified regular HD models, correcting the Power-Wagon-only title emphasis. Exact selected-part retailer tables restore 3500 Laramie 2017-2018. All original thirteen named rows and bounds remain, including Lone Star 2017 only. No 2016 earlier sensor arrangement, diesel or later-generation application is inferred.
| Years | Make | Model | Named trim; actual engine and hood requirements apply |
|---|---|---|---|
| 2017-2018 | Ram | 2500 | Big Horn |
| 2017-2018 | Ram | 2500 | Laramie |
| 2017-2018 | Ram | 2500 | Laramie Longhorn |
| 2017-2018 | Ram | 2500 | Limited |
| 2017-2018 | Ram | 2500 | Power Wagon |
| 2017-2018 | Ram | 2500 | SLT |
| 2017-2018 | Ram | 2500 | Tradesman |
| 2017-2018 | Ram | 3500 | Big Horn |
| 2017-2018 | Ram | 3500 | Laramie Longhorn |
| 2017-2018 | Ram | 3500 | Limited |
| 2017 | Ram | 3500 | Lone Star |
| 2017-2018 | Ram | 3500 | SLT |
| 2017-2018 | Ram | 3500 | Tradesman |
| 2017-2018 | Ram | 3500 | Laramie |
Verify 54-72104 against the actual engine, sensor and vent connections, mounting locations and applicable emissions requirements before ordering.
| Brand | aFe POWER |
| Manufacturer Part Number | 54-72104 |
| Product line | Momentum GT cold air intake |
| Selected filter | One 24-91110 Pro 5R; five oiled cotton-gauze layers; metal reinforcement; 8-inch height |
| Filter dimensions | 6-inch flange; 8-inch base and inverted top |
| Main materials | Molded XLPE housing and tube; silicone coupling; aluminum CCV fitting |
| Sensor configuration | No MAF; original temperature sensor transfers |
| Temperature fitting qualification | Primary calls injection molded; manual calls billet. Actual supplied material/revision remains qualified |
| Mounting | Two original lower grommets, two supplied side grommets and retained AC-line isolation mount |
| Bench flow | Selected Pro 5R 590 versus original 435 CFM at 7 inches H2O; approximately 35.6% |
| Dyno qualification | Actual linked earlier 2016 54-72103 V2 basis; marked +15.44 hp / +14.45 lb-ft versus maxima +15.42 hp / +11.68 lb-ft |
| Emissions | Current manufacturer and own manual state not CARB exempt |
| UPC | 802959543627 |
| WARNING | This product can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and reproductive harm. For more information go to www.P65Warnings.ca.gov. |
| Quantity | Manufacturer service part | Component |
|---|---|---|
| 1 | 24-91110 | Selected Pro 5R oiled reinforced filter |
| 1 | 05-72104B1 | Intake tube |
| 1 | 05-72103B2 | Housing |
| 1 | 05-00937 | Airbox plug |
| 1 | 03-50267 | Large T-bolt clamp |
| 1 | 03-50032 | M6 hex-head bolt; length unspecified |
| 1 | 03-50070 | M6 flat washer |
| 1 | 03-50071 | M6 lock washer |
| 2 | 03-50537 | Urethane side-tab grommets |
| 1 | 05-01339 | Large CCV fitting |
| 1 | 03-50167 | Rubber sensor-fitting grommet |
| 1 | 05-01454 | Air-temperature sensor fitting |
| 1 | 05-01389 | Silicone coupling; manual labels hump, primary describes double hump |
| 2 | 03-50498 | Smaller T-bolt clamps, 3-9/16 to 3-7/8 inches |
Shared-bill dry and Pro-GUARD elements are alternatives, not additional supplied filters. Reuse the original air duct, two lower rubber housing grommets, remaining AC-line isolation mount, IAT, CCV hose and engine cover. One AC-line isolation mount is removed as illustrated; the remaining one slides into alignment with the new housing threaded insert. The primary and manual disagree on temperature-adaptor material; neither changes the actual sensor interface. The tube and housing are molded plastic, so the inaccurate Carbon Fiber product tag is removed separately with protected verification. No global collection rules change.
aFe Power develops application-specific intake, filtration, exhaust, cooling, tuning, suspension, drivetrain, and truck-performance components supported by product testing and documented installation requirements.
One 24-91110 Pro 5R oiled filter with five cotton-gauze layers, metal reinforcement and 8-inch height.
Is this limited to Power Wagon?Current manufacturer and exact manual also identify qualified 2017-2018 Ram 2500/3500 6.4L configurations without MAF.
Does a MAF transfer?This exact newer configuration has no intake MAF. The original temperature sensor transfers to the supplied adaptor.
How does the AC line attach?The retained isolation mount slides into alignment with the housing rear insert and attaches using supplied M6 bolt and both washers.
Are all four housing grommets new?No. Two original lower rubber grommets transfer, and two supplied urethane grommets fit the side tabs.
Should the CCV fitting bottom out?No. It is NPT, must not be overtightened and retains a normal gap between the hex and tube.
Does the linked dyno independently test this newer no-MAF version?It identifies the earlier 2016 54-72103 V2 tube and is qualified historical manufacturer evidence.
What torque and follow-up apply?No numeric torque or M6 bolt length is specified. Check bolts, clamps and connectors after 100-200 miles and verify engine-cover clearance.
Verify aFe 54-72104. Read all twenty pages and figures A-N. Work on a cool engine and disconnect negative battery terminal. Release engine-cover front mounts and pull forward to unclip rear mounts. Disconnect IAT and original CCV hose, loosen original tube clamps and remove tube. Remove upper airbox and filter, release AC-line fasteners and other hard/coolant-line retention. Lift housing from posts while still in vehicle, release original air duct tabs and remove housing and duct. Remove the illustrated AC-line isolation mount. Transfer two original lower grommets to new housing and fit both supplied side-tab urethane grommets. Reconnect original air duct. Fit sensor grommet/adaptor and original IAT. Install CCV NPT fitting without overtightening; a gap at its hex is normal. Seat housing and duct on all four mounts. Slide retained AC isolation mount to align with rear threaded insert and attach using supplied M6 bolt, lock washer and flat washer. Fit selected filter and large housing clamp loosely. Fit silicone coupling and smaller clamps loosely at throttle body. Install tube while prealigning original CCV hose, then ensure no gap around tube end and filter flange. Align and tighten clamps with engine-cover clearance checked. Reconnect IAT and click CCV hose past adaptor step, then tug-check retention. Restore rear and front engine-cover mounts and fit optional airbox plug if desired. No numeric torque is stated. Check bolts, clamps and connectors after 100-200 miles.
Actual family bench chart shows selected Pro 5R 590 versus original 435 CFM at 7 inches H2O, approximately 35.6 percent, rounded to 36 percent. Dry 550 and Pro-GUARD 540 CFM are different media. Current manufacturer links a dyno that actually identifies a 2016 Power Wagon and earlier 54-72103 V2 tube; it is qualified historical manufacturer basis, not a new independent 2017-2018 no-MAF configuration test. Marked 5613-rpm differences are 15.44 hp and 14.45 lb-ft, while run maxima differ by 15.42 hp and 11.68 lb-ft. Both runs September 2, 2016 use original tuner, headers and exhaust, 10 percent preload, blade fan and second gear; intake notes auxiliary scoop covered. Baseline SAE 1.03 versus intake 1.01 and weather differ. Current manufacturer and exact manual state not CARB exempt and unavailable for purchase in California or use on California-registered vehicles; the older CARB Yes copy is corrected. Turn14 authenticated access is unavailable; prices remain unchanged.
California Proposition 65 warning: this product can expose you to chemicals known to the State of California to cause cancer and reproductive harm.
Shop aFe POWER intake systems, replacement filters, exhaust components, BladeRunner cooling parts and CONTROL chassis accessories at Black Ops Auto Works. Compare Momentum GT, Track Series and Magnum FORCE intake applications alongside Pro DRY S and Pro 5R filter choices. Choose a complete upgrade or a service component for the system already on your car, truck or SUV.Choose Your aFe Intake and FilterMomentum GT, Track Series and Magnum FORCECompare the intake housing, tubing, filter arrangement and finish offered for your engine. The collection includes Momentum GT applications, selected carbon-fiber Track Series systems and Magnum FORCE configurations. Each package supplies its own combination of induction components, so choose the design for the installation you want.Pro DRY S or Pro 5R Filter MediaPro DRY S uses oil-free media and skips the re-oiling step during service. Pro 5R is an oiled filter option with a different maintenance procedure. Choose a media configuration aFe off...
View aFe Products
Shop performance air intake systems for your next engine-bay upgrade at Black Ops Auto Works. Compare complete cold-air intakes, short-ram layouts and enclosed systems from Legmaker, JLT, aFe, K&N, Injen and other listed manufacturers. Choose the intake character, packaging and filter-service approach that suit the vehicle and the way you use it.Complete Intakes or a Focused Component UpgradeA complete intake is the place to start when changing the filter, tubing and enclosure as a matched package. An individual airbox, intake tube, coupler or replacement filter can be a better purchase when the rest of the installed system is staying. Compare what the package supplies before choosing between the two routes.For a naturally aspirated, turbocharged or supercharged engine, the connection and sensor arrangement are part of the design. Choose the complete system for that application rather than combining a large tube and filter solely by appearance.Cold-Air, Short-Ram and Enclosed De...
View Air Intake Systems Products
Shop cold air intakes, short-ram systems, closed-airbox packages and intake tubes at Black Ops Auto Works. Compare Legmaker carbon-fiber layouts with aFe, K&N, Injen, AEM, JLT, CORSA, Volant and other listed options. Choose the filter location, inlet connection, service requirements and induction character that suit the vehicle and build.Choose the Intake LayoutA closed-airbox system encloses the filter and uses its specified air-feed arrangement. An open-element or short-ram layout places the filter differently and can change the audible induction character. A longer routed intake, a short-ram system and a factory-airbox tube replacement involve different installation scopes.Compare the actual filter position, heat-shield/enclosure design, retained ducts and access for maintenance. A cold-air label alone does not establish a lower inlet temperature in every driving condition or a fixed horsepower gain. Review manufacturer testing for the exact system and application.Legmaker HE...
View Cold Air Intakes Products
Shop Ram 2500 parts for chassis projects, diesel maintenance and everyday truck use at Black Ops Auto Works. Explore Bilstein shocks and leveling options, Synergy steering or suspension components, Fleece fuel-system parts and bed accessories. Choose the next step around your truck configuration and the work you have planned.Shocks, Leveling and Steering ComponentsCompare the listed B8 5162 front leveling kit with replacement-shock choices for your existing suspension. Bilstein, KYB and other references distinguish axle, drivetrain and ride height. Synergy tie rods, track bars and sway-bar links provide separate project options. Keep Power Wagon, factory rear-air and lifted applications distinct when selecting the exact components.Cummins Fuel and Cooling ServiceFor a 6.7L Cummins truck, review Fleece under-bed filter assemblies and heater kits by production range. Compare applicable intake, radiator and coolant-pipe references with the service you are planning. Injector and transmi...
View Ram 2500 Parts and Accessories Products
Shop Ram 3500 parts for suspension work, Cummins maintenance and practical truck upgrades at Black Ops Auto Works. Compare Bilstein leveling and replacement-shock options, reservoir-shock applications, Fleece fuel-filter components and bed protection. Plan each purchase around the truck and equipment you use.Leveling Kits and Shock ChoicesThe listed Bilstein B8 5112 front leveling kit names 2013–2026 Ram 3500 4WD coverage. Compare it with B6 4600 replacement-shock references or the listed King rear-reservoir application for the appropriate vehicle. Choose the actual ride-height range, axle and factory suspension configuration before comparing construction and adjustment features.Cummins Fuel, Cooling and Transmission PartsReview Fleece under-bed filter assemblies and separate heater kits for the specified production ranges. Intake, radiator and coolant-pipe choices support different maintenance or installation plans. For a transmission project, match the actual 68RFE or Aisin applic...
View Ram 3500 Parts and Accessories Products
