aFe 56-70006R is the Takeda Momentum enclosed intake for the specified Mazda MX-5 Miata ND 2.0L applications. One Pro 5R filter fits the XLPE window housing and tube. The silicone bellows uses a supplied elbow and replacement PCV hose, the original MAF transfers, and a vinyl cap closes the disconnected sound-tube fitting.
Current exact manufacturer pages list Mazda MX-5 Miata ND 2016–2026 with the 2.0L engine; the linked 16-page manual ends at 2020. Each selected-part CI Motorsports table explicitly supports the named rows below, including later 2026 standard trims and the two 2020 100th Anniversary rows plus 2025 35th Anniversary. Later rows are qualified beyond the manual. Mazda identifies the U.S. 35th Anniversary as soft-top only; retailer RF 35th Anniversary rows are not adopted. This is not an approval for the international 1.5L engine or a related Fiat turbo application. Both exact pages expressly allow the separately purchased Silver Bullet throttle-body spacer 46-30001.
| Years | Make | Model | Named trim; actual engine and hood requirements apply |
|---|---|---|---|
| 2020 | Mazda | MX-5 Miata | 100th Anniversary Special Edition |
| 2025 | Mazda | MX-5 Miata | 35th Anniversary |
| 2016-2026 | Mazda | MX-5 Miata | Club |
| 2016-2026 | Mazda | MX-5 Miata | Grand Touring |
| 2020 | Mazda | MX-5 Miata | RF 100th Anniversary Special Edition |
| 2017-2026 | Mazda | MX-5 Miata | RF Club |
| 2017-2026 | Mazda | MX-5 Miata | RF Grand Touring |
| 2016-2026 | Mazda | MX-5 Miata | Sport |
Verify 56-70006R against the actual engine, sensor and vent connections, mounting locations and applicable emissions requirements before ordering.
| Brand | aFe POWER |
| Manufacturer Part Number | 56-70006R |
| Product type | Takeda Momentum enclosed cold air intake |
| Selected filter | One 24-91103, 3.5-inch flange x 5-inch base x 4.5-inch inverted top x 7.5-inch height |
| Media | Five-layer pre-oiled cotton gauze; washable/reusable |
| Tube / housing | XLPE 05-5670006B1 / window housing 05-5670006B2 |
| Bellows / clamps | 05-01497 / two #044 03-50019, plus illustrated filter-flange clamp |
| PCV hose / elbow | 05-01503, 3/8-inch ID x 13-inch length / 03-50151 |
| MAF screws / tool | Two M4 x 10mm 03-50490 / T20 bit 03-50066 |
| Mount / cap / plug | Silicone 03-50534 / vinyl 03-50548 / housing plug 05-00937 |
| Torque / interval | No numeric torque or mileage interval in exact linked manual |
| Quantity | Manufacturer service part | Component |
|---|---|---|
| 1 | 24-91103 | Selected filter; alternate media is not a second supplied filter |
| 1 | 05-5670006B1 | XLPE intake tube |
| 1 | 05-5670006B2 | XLPE window housing |
| 1 | 05-01497 | Silicone bellows |
| 1 | 05-00937 | Auxiliary-inlet housing plug |
| 2 | 03-50019, #044 | Bellows clamps |
| 1 | 05-01503 | 3/8-inch ID x 13-inch silicone PCV hose |
| 2 | 03-50490 | M4 x 10mm MAF screws |
| 1 | 03-50066 | T20 Torx bit |
| 1 | 03-50534 | Silicone housing mount |
| 1 | 03-50548 | Vinyl sound-tube cap |
| 1 | 03-50151 | PCV elbow fitting |
The exact current pages identify Momentum; older Stage-2 listing wording and the linked flow-chart Rapid Ind header do not change the enclosed configuration. The D-page generic feature bullet says Pro 5R, but its dedicated media description and exact alternate BOM identify oil-free Pro DRY S. The manual tells the installer to tighten three worm clamps, while its BOM separately lists only two #044 clamps; the filter-flange clamp has no separate service code/count. Retain the original housing bolt, bushing, collar and lower grommet, and install the supplied silicone mount separately. The housing plug is listed although the illustrated steps do not give a plug-installation step. No MAF extension, check-valve hose or numeric torque is listed. Spacer and cleaning supplies are separate.
aFe Power develops application-specific intake, filtration, exhaust, cooling, tuning, suspension, drivetrain, and truck-performance components supported by product testing and documented installation requirements.
One 24-91103 Pro 5R filter; the alternate-media BOM row is not a second supplied filter.
Does the D version need oil?No. Its dedicated description specifies three-layer oil-free synthetic, despite a generic Pro 5R feature bullet.
How does the PCV hose connect?The supplied elbow fits the bellows port; the supplied 13-inch silicone hose connects it to the valve-cover fitting.
What happens to the sound tube?Remove its intake-side assembly and close the remaining fitting with the supplied vinyl cap.
Which mounts are reused?One original lower grommet plus the original housing bolt, top bushing and metal collar; install the supplied silicone mount separately.
Is the MAF sensor or an extension supplied?Transfer the original MAF with two M4 x 10mm screws; no extension harness is listed.
Can the aFe throttle-body spacer be used?Both exact manufacturer pages explicitly allow the separately purchased 46-30001 spacer.
What torque and recheck interval apply?The exact manual supplies neither a numeric torque nor a mileage interval.
Verify aFe 56-70006R. Work on a cool engine and disconnect the negative battery terminal as directed. Disconnect the MAF harness, release its clip and unclip the coolant-reservoir line from the housing. Retain the housing bolt, rubber bushing and metal collar. Disconnect the original PCV hose at the valve cover, loosen the tube clamps, release the two upper-housing clips and remove the upper housing. Unclip and remove the intake coupling and sound-tube assembly, then cap the remaining sound-tube fitting with the supplied vinyl cap. Remove the lower housing. Transfer one original lower grommet and install the supplied silicone mount in the new housing; transfer the bushing and metal collar to its top mount. Push the filter into the housing until it locks. Lower and secure the housing using the original bolt. Fit the bellows and its two clamps at the throttle body, insert the tube into the bellows and its larger end into the filter, then align and tighten all three worm clamps as directed. Insert the elbow into the bellows port and connect the supplied silicone PCV hose between that fitting and the valve-cover fitting. Transfer the MAF with the supplied M4 x 10mm screws and reconnect its harness. Restore the negative battery connection before operation and check the retained lines and all connections. The manual supplies no numeric torque or mileage recheck interval; do not borrow 100–200 miles from another kit.
The current exact page claims 220 CFM and 13% flow increase. However, its linked 56-70006 chart has a Rapid Ind header and shows Pro 5R 230 CFM, Pro DRY S 220 CFM and stock 200 CFM at 7 inches H2O. These are inconsistent source values and are not combined into one certified percentage. The selected-media Dynojet image shows an OE-intake/OE-exhaust baseline January 10, 2019, fourth gear and a blade fan. The February 28, 2019 selected-intake run retains OE exhaust/fourth gear/blade fan and explicitly has the housing plug removed. Baseline SAE factor is 1.00; intake factor is 1.00; both use smoothing 5. At marked 6,585 rpm, 167.02 versus 160.98 hp and 133.21 versus 128.40 lb-ft differ by 6.04 hp and 4.81 lb-ft. Independent maxima 167.05 versus 162.39 hp differ by 4.66 hp; 150.42 versus 148.35 lb-ft differ by 2.07 lb-ft. The image does not state a model year, fuel or starting rpm to infer. Marked-point and independent-peak comparisons differ, and individual results vary. The current manufacturer pages state this product is not CARB exempt and unavailable for purchase in California or use on California-registered vehicles. The older manual separately restricts public-road use in California and states adopting its emissions rules; its race-use wording is not street-use exemption evidence.
California Proposition 65 warning: this product can expose you to chemicals known to the State of California to cause cancer and reproductive harm.
Shop aFe POWER intake systems, replacement filters, exhaust components, BladeRunner cooling parts and CONTROL chassis accessories at Black Ops Auto Works. Compare Momentum GT, Track Series and Magnum FORCE intake applications alongside Pro DRY S and Pro 5R filter choices. Choose a complete upgrade or a service component for the system already on your car, truck or SUV.Choose Your aFe Intake and FilterMomentum GT, Track Series and Magnum FORCECompare the intake housing, tubing, filter arrangement and finish offered for your engine. The collection includes Momentum GT applications, selected carbon-fiber Track Series systems and Magnum FORCE configurations. Each package supplies its own combination of induction components, so choose the design for the installation you want.Pro DRY S or Pro 5R Filter MediaPro DRY S uses oil-free media and skips the re-oiling step during service. Pro 5R is an oiled filter option with a different maintenance procedure. Choose a media configuration aFe off...
View aFe Products
Shop performance air intake systems for your next engine-bay upgrade at Black Ops Auto Works. Compare complete cold-air intakes, short-ram layouts and enclosed systems from Legmaker, JLT, aFe, K&N, Injen and other listed manufacturers. Choose the intake character, packaging and filter-service approach that suit the vehicle and the way you use it.Complete Intakes or a Focused Component UpgradeA complete intake is the place to start when changing the filter, tubing and enclosure as a matched package. An individual airbox, intake tube, coupler or replacement filter can be a better purchase when the rest of the installed system is staying. Compare what the package supplies before choosing between the two routes.For a naturally aspirated, turbocharged or supercharged engine, the connection and sensor arrangement are part of the design. Choose the complete system for that application rather than combining a large tube and filter solely by appearance.Cold-Air, Short-Ram and Enclosed De...
View Air Intake Systems Products
Shop cold air intakes, short-ram systems, closed-airbox packages and intake tubes at Black Ops Auto Works. Compare Legmaker carbon-fiber layouts with aFe, K&N, Injen, AEM, JLT, CORSA, Volant and other listed options. Choose the filter location, inlet connection, service requirements and induction character that suit the vehicle and build.Choose the Intake LayoutA closed-airbox system encloses the filter and uses its specified air-feed arrangement. An open-element or short-ram layout places the filter differently and can change the audible induction character. A longer routed intake, a short-ram system and a factory-airbox tube replacement involve different installation scopes.Compare the actual filter position, heat-shield/enclosure design, retained ducts and access for maintenance. A cold-air label alone does not establish a lower inlet temperature in every driving condition or a fixed horsepower gain. Review manufacturer testing for the exact system and application.Legmaker HE...
View Cold Air Intakes Products
Shop Mazda Miata brake parts, dampers, engine components and exhaust options at Black Ops Auto Works. Compare DFC and Brembo brakes, Bilstein suspension choices and generation-specific body or cabin accessories. Choose by exact engine, roof or body configuration and installed equipment to coordinate your project.Brake Service by Generation and PackageChoose DFC rotors, pads, hoses and hardware by complete Miata generation and production coverage, matching axle, installed caliper and rotor dimensions. Review master-cylinder applications separately for ABS and other system requirements. Compare compounds and kit contents only within the correct brake-package application.Bilstein Dampers and Chassis ProjectsDisplayed Bilstein B6 and B8 references have separate generation, position and production coverage. KYB, SuperPro, Cusco and SPL references support different damper, bush or alignment tasks. Match actual chassis and factory equipment, then review installation scope and any required ...
View Mazda Miata Parts and Accessories Products
Shop Mazda MX-5 Miata cooling hoses, brake parts, dampers and exhaust options at Black Ops Auto Works. Compare Mishimoto and do88 hose choices, DFC or Brembo brakes, Bilstein suspension components and MBRP or GReddy axle-backs. Choose by exact generation, engine, roof or body configuration and installed equipment.Cooling Hoses and Engine-Service ProjectsChoose Mishimoto coolant hoses and do88 ND coolant or vacuum-hose sets by their separate complete engine and system applications. Match routing, connections and supplied pieces to the installation. Select Boundary oil pumps and ATI dampers independently by the actual engine, crank and accessory-drive configuration for the service or build.DFC and Brembo Brake MaintenanceCompare DFC rotors, pads, hoses and master cylinders by complete Miata generation, axle and brake-system coverage. Match installed caliper, rotor dimensions and ABS configuration where specified. Review Brembo pad-and-rotor kits by their own full applications and cont...
View Mazda MX-5 Miata Parts and Accessories Products
