Click to zoom in
Deep Hurricane Exhaust Tone with Black-Tip Style
Give your 2025–2026 Ram 1500 Standard-Output 3.0L twin-turbo Hurricane a deeper voice with the aFe POWER Vulcan cat-back exhaust. Part 49-32088-1B combines 3-inch mandrel-bent stainless steel tubing, an acoustically tuned expansion chamber and dual black 5-inch tips. Built for Crew Cab trucks with the 5-foot-7-inch bed, it uses the factory mounting points for a precise installation.
Key Features
- 3-inch mandrel-bent stainless steel tubing designed for smooth exhaust flow.
- Acoustically tuned expansion chamber delivers a deep, throaty exhaust note.
- Dual black clamp-on tips with 5-inch outlets and aFe logo plates.
- MIG-welded construction and factory-style flange and hanger locations.
- aFe reports gains of up to 19 horsepower and 30 lb-ft of torque; actual results depend on the vehicle and conditions.
- Designed and manufactured at aFe POWER's Corona, California facility.
Fitment
| Years | Vehicle | Engine | Cab and Bed |
|---|---|---|---|
| 2025–2026 | Ram 1500 | Standard-Output 3.0L twin-turbo inline-six Hurricane | Crew Cab, 5-foot-7-inch bed |
49-32088-1B does not fit High-Output Hurricane engines or RHO models. Match the engine output, cab and bed configuration before ordering.
Specifications
| Detail | Value |
|---|---|
| Manufacturer | aFe POWER |
| Series | Vulcan |
| Manufacturer Part Number | 49-32088-1B |
| System Type | Cat-back exhaust |
| Tubing Diameter | 3 inches |
| Construction | Mandrel-bent stainless steel, MIG welded |
| Exit | Dual rear |
| Tip Finish | Black |
| Tip Dimensions | 4-inch inlet, 5-inch outlet, 12-inch length |
| Sound Design | Acoustically tuned expansion chamber |
What's Included
- 49-32088-1B expansion chamber assembly.
- Driver-side and passenger-side over-axle pipes and tailpipes.
- Left and right black bolt-on exhaust tips.
- Four 3-inch band clamps and two M10 flange nuts.
The installation guide specifies reuse of the factory flange bolts and gasket.
About aFe POWER
aFe POWER develops performance intake and exhaust products for automotive enthusiasts. Its Vulcan exhaust systems are engineered and manufactured in Corona, California, with application-specific routing and mounting.
Related Parts
- aFe Momentum GT Cold Air Intake with Pro 5R Filter for Ram 1500 3.0L — a separate intake upgrade; check the intake's application and emissions requirements for your truck.
FAQ
What is the 49-32088-1B?It is an aFe POWER Vulcan cat-back exhaust with black tips for the 2025–2026 Ram 1500 Standard-Output 3.0L Hurricane, Crew Cab with a 5-foot-7-inch bed.
Does it fit the High-Output Hurricane or RHO?No. aFe explicitly excludes High-Output Hurricane engines and RHO models.
Which cab and bed does it fit?The manufacturer installation guide specifies Crew Cab trucks with the 5-foot-7-inch bed.
How large are the exhaust tubing and tips?The tubing is 3 inches in diameter. Each black tip has a 4-inch inlet, a 5-inch outlet and a 12-inch length.
What sound should I expect?The tuned expansion chamber is designed to produce a deep, throaty exhaust tone. Sound varies with driving conditions and vehicle configuration.
Does installation require cutting?The new system mounts to factory locations. aFe notes that removing the original exhaust without a vehicle lift may require cutting the original system.
What power gains does aFe report?aFe advertises gains of up to 19 horsepower and 30 lb-ft of torque. These are manufacturer-reported maximum gains, not a guarantee for every truck.
Is installation hardware supplied?Yes. The kit includes band clamps and flange nuts. The guide calls for reuse of the factory flange bolts and gasket.
Can this exhaust be drop shipped?This is a special-order item. Turn 14 currently reports no stock at aFe and estimated fulfillment of 45–58 days, subject to supplier confirmation. Manufacturer drop shipment is supported when stock is available.
Installation Instructions
Professional installation is recommended. Read the manufacturer installation guide for 49-32088-1B before beginning.
- Let the exhaust cool, use appropriate protective equipment and support the truck at its approved lifting points.
- Support the factory exhaust and remove its tips, tailpipes, over-axle section and muffler assembly following aFe's guide.
- Install the expansion chamber using the factory flange bolts and gasket with the supplied nuts.
- Fit the over-axle pipes, tailpipes and black tips. Keep the connections loose while aligning the system.
- Confirm safe clearance from the body, tires, brake lines, wiring and hoses. Tighten fasteners according to the manufacturer guide.
- Check for leaks, then recheck and retighten the hardware after 50–100 miles as aFe directs.
California Proposition 65 Warning
WARNING: Cancer and Reproductive Harm. www.P65Warnings.ca.gov
aFe
Shop aFe Power cold air intakes, air filters, exhaust systems, intercoolers, charge pipes, tuning modules, suspension parts, drivetrain components, and truck accessories. Match every part by exact aFe manufacturer number and verify the complete vehicle, engine, drivetrain, emissions classification, dimensions, and included hardware before ordering. Cold Air Intakes and Performance Filters Choose an aFe intake by exact vehicle and engine application, then compare tube design, sensor provisions, housing configuration, emissions status, and filter media. Pro DRY S dry media is serviced without filter oil, while oiled media options follow their own cleaning and re-oiling procedures. Replacement and universal filters must be matched by flange size, panel dimensions, seal design, height, and airflow direction. aFe Power Exhaust Systems and Emissions Fitment Cat-back, axle-back, DPF-back, header, downpipe, mid-pipe, and related exhaust parts can vary by body style, cab and bed, wheelbase...
View aFe Products
Catback
A catback exhaust system replaces everything from the catalytic converter back, covering the mid pipe, muffler, and tailpipe section in one bolt on upgrade. This collection covers catback systems for trucks, Jeeps, muscle cars, imports, and performance SUVs, giving you a straightforward way to improve sound, exhaust flow, and rear end styling without touching the factory catalytic converters or front pipe. Catback systems are available in stainless steel and titanium construction, with dual rear exit, single exit, and quad tip configurations, and a range of sound levels from mild touring tone to aggressive track character. Whether you want a deeper daily driver sound or a full track ready exhaust note, you will find a matched system for your platform here. What This Category Covers This collection includes complete catback exhaust systems, cat-back kits, dual rear exit systems, axle back adjacent catback upgrades, stainless steel and titanium exhaust systems, and street, tourin...
View Catback Products
Exhaust Systems
Shop performance exhaust systems, cat-backs, axle-backs, headers, mufflers, and exhaust tips at Black Ops Auto Works. Compare options from Borla, CORSA, Solo Performance, AWE, MagnaFlow, MBRP, Kooks, Akrapovic, Invidia, and other brands. Find complete systems and individual components for muscle cars, performance SUVs, trucks, imports, and European vehicles. Cat-Back and Axle-Back Exhaust Systems Choose the exhaust section that matches your project. Cat-back systems generally replace the exhaust downstream of the catalytic converter, while axle-back systems replace the rear section. Exact connection points and package contents vary by vehicle. Compare muffler design, pipe diameter, exit location, tip configuration, and compatibility with existing exhaust components. Exhaust for HEMI, SRT, Trackhawk, and Hellcat Vehicles This collection includes exhaust options for selected Jeep Grand Cherokee SRT and Trackhawk, Dodge Durango SRT and Hellcat, Dodge Charger, Chrysler 300, and Ram appl...
View Exhaust Systems Products