Click to zoom in
The Akrapovic S-AU/TI/20H Evolution Line Cat Back (Titanium) with Carbon Fiber and Titanium Tips is the definitive exhaust upgrade for the 2020 to 2025 Audi RS Q8 (4ML) with the 4.0L V8 TFSI biturbo engine. Hand-crafted at Akrapovic's Slovenia facility from aerospace-grade titanium, the S-AU/TI/20H replaces the entire factory catback system and delivers a documented gain of 12 kW (16 HP) at 5,500 rpm, 25 Nm (18 lb/ft) at 2,000 rpm, and an extraordinary 19.1 kg (42.1 lbs) weight reduction versus the OEM system. The signature hexagonal titanium muffler bodies with carbon fiber end caps and four 120mm carbon fiber inlet with titanium outer tips transform the RS Q8's rear visual presentation while the carefully tuned Akrapovic sound chambers unlock the deep, layered V8 exhaust note that the factory system actively suppresses. The S-AU/TI/20H is for RS Q8 owners who want the complete performance and sound transformation, not just an incremental improvement.
Key Features
- Full Titanium Catback Assembly - Every component from cats to tailpipe is hand-welded aerospace titanium, delivering a 19.1 kg (42.1 lb) weight reduction over the factory system while providing superior corrosion resistance and thermal management for track and high-performance street use.
- Carbon Fiber and Titanium Quad Tips - Four 120mm round tips with carbon fiber inner inlet sections and brushed titanium outer bodies provide a striking, race-derived visual upgrade at the RS Q8's rear diffuser, transforming the standard exhaust appearance.
- Dyno-Proven Power Gains - Akrapovic's independent dyno testing confirms +12 kW (16 HP) at 5,500 rpm and +25 Nm (18 lb/ft) at 2,000 rpm on a stock RS Q8 4.0L V8 TFSI with no supporting modifications required.
- Signature Hexagonal Muffler Design - The iconic Akrapovic hexagonal muffler bodies with carbon fiber end caps deliver acoustic tuning benefits alongside the distinctive visual profile associated with Akrapovic's top-tier production exhaust systems.
- 42-Pound Weight Reduction - The S-AU/TI/20H system weighs 12.6 kg (27.8 lbs) versus the factory 31.7 kg (69.9 lbs) system, removing 19.1 kg (42.1 lbs) from a vehicle that benefits significantly from rear mass reduction.
- EC Homologated - The S-AU/TI/20H carries European EC homologation for street-legal use across applicable markets. Always verify local regulations for street-use compliance.
- Direct Bolt-On Fitment - Uses OEM mounting points and supplied hardware. No cutting, welding, or chassis modification required for 2020 to 2025 RS Q8 4ML chassis vehicles.
- Lifetime Warranty - Backed by Akrapovic's lifetime warranty against manufacturing defects for the original purchaser.
Fitment
| Year Range | Make | Model | Trim |
|---|---|---|---|
| 2020-2025 | Audi | RS Q8 | Prestige 4.0L V8 TFSI (4ML) |
| 2020-2025 | Audi | RS Q8 | Performance 4.0L V8 TFSI (4ML) |
Specifications
| Detail | Value |
|---|---|
| MPN | S-AU/TI/20H |
| UPC | 3831113504287 |
| Brand | Akrapovic |
| System Type | Evolution Line Cat Back (Titanium) |
| Material | Titanium with Carbon Fiber and Titanium Tips |
| System Weight | 12.6 kg (27.8 lbs) |
| Weight Savings vs. Stock | 19.1 kg (42.1 lbs) |
| Power Increase | +12 kW (16 HP) at 5,500 rpm |
| Torque Increase | +25 Nm (18 lb/ft) at 2,000 rpm |
| Tip Style | 120mm Carbon Fiber/Titanium Quad Round (4x) |
| Muffler Design | Hexagonal with Carbon Fiber End Caps |
| Compatible Engine | 4.0L V8 TFSI Biturbo |
| Homologation | EC Approved |
| Country of Origin | Slovenia |
| Warranty | Lifetime against manufacturing defects |
What's Included
- Titanium muffler set (S-AU/T/20H)
- Titanium link pipe set (S-AU/1)
- 4x 120mm carbon fiber and titanium exhaust tips
- Stainless steel clamps and mounting hardware
- Akrapovic installation instructions
Frequently Asked Questions
Does the Akrapovic S-AU/TI/20H fit the Audi RS Q8 Prestige and RS Q8 Performance for 2020 through 2025?Yes. The S-AU/TI/20H is designed for all 2020 to 2025 Audi RS Q8 (4ML) variants with the 4.0L V8 TFSI biturbo engine, including the Prestige and Performance trims sold in North America.
How much does the Akrapovic S-AU/TI/20H weigh compared to the factory RS Q8 exhaust?The S-AU/TI/20H system weighs 12.6 kg (27.8 lbs). The factory RS Q8 catback weighs 31.7 kg (69.9 lbs). The Akrapovic system removes 19.1 kg (42.1 lbs) from the rear of the vehicle, which measurably improves weight distribution, rear axle load, and brake performance.
What power and torque gains does the Akrapovic S-AU/TI/20H add to the Audi RS Q8?Akrapovic's dyno testing records a gain of 12 kW (16 HP) at 5,500 rpm and 25 Nm (18 lb/ft) at 2,000 rpm on a stock RS Q8 with no other modifications. The gains are realized without ECU tuning.
Does the Akrapovic RS Q8 catback require ECU tuning or coding?No. The S-AU/TI/20H is a direct bolt-on catback that retains all factory catalytic converters and oxygen sensors. The Audi RS Q8 factory ECU does not require modification or recalibration for this installation.
Will the Akrapovic S-AU/TI/20H trigger a check engine light on my Audi RS Q8?No. Because the S-AU/TI/20H retains the factory catalytic converters and all OEM oxygen sensor mounting positions, no fault codes or check engine lights are generated on a stock RS Q8 with this installation.
What do the carbon fiber and titanium tips look like on the RS Q8?The S-AU/TI/20H uses four 120mm round tips with carbon fiber inlet rings and brushed titanium outer bodies. The tips fill the RS Q8's rear diffuser cutouts with a visually dramatic, asymmetric carbon and titanium finish that replaces the factory chrome tips entirely.
Does the Akrapovic S-AU/TI/20H work with the Audi RS Q8's active exhaust sound valve system?The S-AU/TI/20H integrates with the RS Q8's factory OPF (Otto Particle Filter) system and active valve wiring. The factory driving mode sound management is retained after installation. The S-AU/TI/20H is the OPF-compatible variant for the 4ML RS Q8.
Is the Akrapovic S-AU/TI/20H street legal in the United States?The S-AU/TI/20H is EC homologated for European road use and is designed for street use. It is not CARB certified. California residents should verify compliance before purchase. For all other US states, this is a street-compatible exhaust system. Always confirm local sound ordinances.
How long does it take to install the Akrapovic S-AU/TI/20H on the Audi RS Q8?A professional installer can complete the S-AU/TI/20H installation in approximately two to four hours. The system is a direct bolt-on replacement at all factory mounting points, but the RS Q8's underfloor packaging requires careful routing of the link pipes for correct alignment.
What warranty does the Akrapovic S-AU/TI/20H carry?The S-AU/TI/20H is backed by Akrapovic's lifetime warranty against manufacturing defects for the original purchaser, covering all components and workmanship for the life of the exhaust system.
Installation Instructions
- Allow the Audi RS Q8 to cool completely before starting. The factory exhaust system and OPF unit retain significant heat after operation.
- Raise and secure the RS Q8 on a lift or appropriately rated jack stands with stable support at all four chassis jack points.
- Disconnect the factory active exhaust valve actuator connectors at the muffler assembly and secure the wiring harnesses clear of the exhaust routing area.
- Loosen and remove all factory clamps at the OPF/catalytic converter outlets on both sides of the vehicle.
- Disconnect and remove all factory hanger isolators along the catback routing path. Support the weight of the factory muffler and link pipe assembly before releasing the final hanger to avoid dropping the system.
- Lower and set aside the factory catback assembly. Inspect all rubber hanger isolators for wear or cracking and replace any deformed isolators before proceeding.
- Install the Akrapovic S-AU/1 titanium link pipes onto the OPF/cat outlets, aligning all flange faces. Attach supplied clamps hand-tight at this stage.
- Connect the S-AU/T/20H titanium muffler set to the link pipe outlets. Hang the muffler assemblies into the factory rubber isolators on both sides.
- Install the 120mm carbon fiber and titanium tips onto the muffler outlets and secure the tip hardware to specification.
- Reconnect the factory exhaust valve actuator connector to the Akrapovic muffler valve port.
- Verify all clamps, hanger connections, and tip hardware are fully engaged before applying final torque. Torque all clamps to the specifications in the Akrapovic instruction sheet.
- Lower the vehicle and start the engine. Run a full idle heat cycle for 10 to 15 minutes. After cooling, re-inspect all joints and re-torque any clamps that shifted during the first thermal cycle.
WARNING: This product can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and reproductive harm. For more information go to www.P65Warnings.ca.gov.
Akrapovic
Akrapovic Exhaust Systems and Carbon Accessories are stocked at Black Ops Auto Works for Porsche 911, BMW M, Audi RS, Ferrari, Lamborghini, McLaren, Mercedes-AMG, C8 Corvette, Nissan GT-R, and select performance motorcycle builds. Shop Slip-On Line titanium exhausts, Evolution Line exhausts, Race Line systems, cat-back systems, link pipes, downpipes, sound kits, carbon fiber tips, titanium tail pipe sets, rear diffusers, and carbon accessories for the correct vehicle and build goal. Every product is filterable by year, make, model, trim, engine, and drivetrain so the correct part ships the first time. Black Ops Auto Works carries 161 Akrapovic Exhaust Systems and Carbon Accessories SKUs across exhaust system layouts, titanium components, tail pipe designs, valve controls, and vehicle-specific platforms. What This Akrapovic Collection Covers Premium titanium exhaust engineering Akrapovic products pair vehicle-specific engineering with titanium construction, precision exhaust rout...
View Akrapovic Products
Carbon Fiber Parts & Accessories
Carbon fiber parts and accessories for Jeep Grand Cherokee, Trackhawk, Dodge Charger, Challenger, Durango, Chrysler 300, Ford Mustang, and Chevrolet Camaro and Corvette are stocked at Black Ops Auto Works. Shop carbon fiber hoods, front splitters, rear spoilers, diffusers, side skirts, mirror covers, headlight covers, badges, and interior trim for Hellcat, Trackhawk, Demon, SRT, and HEMI 6.2L and 6.4L platforms. Every part is filterable by year, make, model, trim, and engine so the correct fitment ships the first time. Black Ops Auto Works carries 2,338 carbon fiber SKUs across hoods, aero, and trim categories. What This Category Covers Carbon fiber parts combine weight reduction with aggressive styling for builds that want a performance look without sacrificing strength. This category spans full hood replacements, splitters and diffusers for aerodynamic upgrades, and smaller trim and badge pieces that finish off an interior or exterior refresh. Why Carbon Fiber Carbon fiber pan...
View Carbon Fiber Parts & Accessories Products
Catback
A catback exhaust system replaces everything from the catalytic converter back, covering the mid pipe, muffler, and tailpipe section in one bolt on upgrade. This collection covers catback systems for trucks, Jeeps, muscle cars, imports, and performance SUVs, giving you a straightforward way to improve sound, exhaust flow, and rear end styling without touching the factory catalytic converters or front pipe. Catback systems are available in stainless steel and titanium construction, with dual rear exit, single exit, and quad tip configurations, and a range of sound levels from mild touring tone to aggressive track character. Whether you want a deeper daily driver sound or a full track ready exhaust note, you will find a matched system for your platform here. What This Category Covers This collection includes complete catback exhaust systems, cat-back kits, dual rear exit systems, axle back adjacent catback upgrades, stainless steel and titanium exhaust systems, and street, tourin...
View Catback Products
Exhaust Systems
Performance exhaust systems for cars, trucks, SUVs, and Jeeps are stocked at Black Ops Auto Works. Shop cat-back systems, axle-back systems, turbo-back systems, headers, downpipes, mid-pipes, mufflers, resonators, catalytic converters, exhaust tips, exhaust valve controllers, oxygen sensors, exhaust brakes, and motorcycle and powersports exhausts for Mustang, Camaro, Challenger, Corvette, Silverado, and Super Duty platforms. Every product is filterable by exhaust position, material, pipe diameter, and vehicle year, make, model, and trim so the correct fitment ships the first time. Black Ops Auto Works carries 7,441 exhaust SKUs across every position of the exhaust system. What This Category Covers Exhaust upgrades change sound, appearance, and in some cases power. Exhaust fitment depends on engine, drivetrain, and factory exit position, so confirm the exact platform before ordering any exhaust component. Exhaust Position Cat-back, axle-back, turbo-back, and header-back systems e...
View Exhaust Systems Products