Keep valve control while gaining clearance behind the Ranger Raptor
The SwitchPath system follows the truck's factory drive-mode and throttle logic while reinforced BashGuard outlets replace vulnerable decorative tips. 3025-38306 is the dual three-inch system for the 3.0L Ranger Raptor SuperCrew.
Key Features
- 3025-38306 exact SwitchPath configuration with BashGuard outlets
- Dual 3-inch mandrel-bent T304L stainless tubing
- Equal-length looped front pipe and tailored X-pipe
- OE-tier valves retain factory drive-mode behavior
- Reinforced high-clearance outlets without decorative tips
- Bolt-on installation with no cutting
- 50-state compliant cat-back design
Fitment
| Years |
Make |
Model |
Verified Application and Notes |
| 2024-2026 |
Ford |
Ranger |
Raptor; 3.0L EcoBoost; 4WD; SuperCrew; 5-foot bed |
| Excluded |
Ford |
Ranger non-Raptor |
Other engines, cabs, beds, and prior generations |
| Excluded |
Ford |
F-150 Raptor |
Different chassis and exhaust layout |
Specifications
| Detail |
Value |
| Manufacturer Part Number |
3025-38306 |
| System |
SwitchPath cat-back |
| Material |
T304L stainless steel |
| Tubing |
Dual 3-inch, 0.065-inch wall |
| Outlet |
Reinforced BashGuard |
| Valve Control |
Factory drive-mode and throttle logic |
| Installation |
Bolt-on; no cutting |
| Emissions |
50-state compliant cat-back |
What's Included
- One complete 3025-38306 SwitchPath cat-back system
- Looped front pipe and X-pipe assembly
- SwitchPath muffler and rear sections
- Reinforced BashGuard outlets
- Additional valve motor, simulator plate, and harness extension
- Clamps and installation hardware
About AWE Tuning
AWE builds stainless performance exhausts around vehicle-specific packaging and sound control. SwitchPath systems combine mechanically valved sections with factory control logic so the truck can retain its selected operating modes.
Related Parts
- Factory valve motor retained for the documented position
- Heat shielding and underbody fasteners inspected during installation
- Skid plates and recovery equipment checked for outlet clearance
FAQ
What is the 3025-38306?It is the AWE SwitchPath cat-back exhaust with reinforced BashGuard outlets for the supported Ranger Raptor.
Does it retain factory exhaust modes?Yes. The valves follow factory drive-mode and throttle behavior when installed with the supplied control components.
Are decorative tips included?No. This configuration ends in reinforced high-clearance BashGuard outlets.
Will it fit a non-Raptor Ranger?No. The verified application is the 3.0L Ranger Raptor SuperCrew with the 5-foot bed.
Is cutting required?No. AWE describes the system as a bolt-on installation with no cutting.
Is an extra valve motor included?Yes. The documented kit includes an additional valve motor plus a simulator plate and harness extension.
Does it fit the F-150 Raptor?No. The F-150 Raptor uses a different chassis and exhaust configuration.
What warranty applies?AWE provides original-owner coverage under its published exhaust warranty, with separate terms for tubing, valves, and electronics.
Installation Instructions
- Verify the carton identifies 3025-38306 and contains the BashGuard outlet configuration.
- Allow the exhaust to cool and support the Ranger Raptor at approved lift points.
- Document factory valve-motor connections and original exhaust alignment before removal.
- Remove the factory cat-back while protecting wiring, skid plates, and heat shields.
- Install the looped front pipe, X-pipe, SwitchPath muffler, and rear sections loosely.
- Fit the valve motor, simulator plate, and harness extension exactly as directed by AWE.
- Set clearance around the spare tire, axle, suspension, skid plates, and rear bumper, then torque all clamps.
- Cycle every exhaust mode, inspect for leaks or contact, and recheck after initial heat cycles.
California Proposition 65 Warning: Cancer and reproductive harm. See www.P65Warnings.ca.gov.
