H&R Trak+ 30mm DRA Wheel Adaptor Bolt 5/120 Center Bore 72.5 Bolt Thread 12x1.5 - Black

Shop BMW 128i parts for the naturally aspirated 3.0L application, with intake, brake and suspension choices matched to body and equipment. Distinguish its induction system from turbocharged 135i components. Intake and Filter Service Injen applications include specified early E82 128i intake kits. Match engine identification, production coverage, airflow-meter connection and the supplied heat shield or mounting pieces. Confirm the installed housing before ordering a replacement filter. An aftermarket intake element can differ from the factory panel filter in both shape and connection. Brakes and Suspension Planning Compare street and competition brake compounds only after confirming caliper, pad shape, rotor dimensions and axle. A rotor-and-pad kit may not include sensors or all fitting hardware. For dampers, mounts or coilovers, record Coupe or Convertible body and use the exact chassis application. Check kit contents, spring compatibility and alignment requirements, including any e...

Find BMW 135i parts with N54 or N55 engine identification established first. Intake connections, charge-cooling hardware and transmission details matter alongside the chassis and body. N54 and N55 Induction Applications BMW’s 2011 135i update introduced the N55 single twin-scroll turbo engine in place of the earlier twin-turbo application. Use engine identification and production details when comparing intake kits or companion components. Injen intake applications separate early twin-intake arrangements from N55 kits. Compare sensor connections, inlet routing, filter arrangement and heat-shield contents for the actual engine. Brakes and Chassis Components Choose pads and rotors by installed caliper, pad shape, axle and rotor dimensions. Review compound characteristics for street or competition use, then account for sensors and hardware. For coilovers and mounts, identify Coupe or Convertible body, chassis and existing suspension changes. Review spring compatibility, mounting content...

Choose BMW 135is parts for its N55 engine and exact Coupe or Convertible configuration. Plan induction, brake and suspension work around the factory equipment and any existing modifications. N55 Powertrain and Installation Scope BMW identifies the 135is with the N55 3.0L single twin-scroll turbo engine. Keep that engine application distinct from earlier N54 intake and charge-system layouts. For an injection or cooling accessory, establish the complete installation requirements. A conversion plate or adapter may require a compatible pump, controller, hoses or existing system; it is not necessarily a complete kit. Brake Compounds and Suspension Details Identify caliper, pad shape, rotor dimensions and axle before comparing street or race pads. Review cold response, operating temperature, bedding and hardware contents for the selected compound. Non-M suspension applications and M-model exclusions still need careful matching. Record body, gearbox, existing spring and damper setup and wh...

Shop BMW 318i parts for the engine and chassis you own, from earlier 3 Series projects to later daily drivers. Focus on the installed suspension, lighting and engine-service equipment. Engine Service Across Generations A 318i badge does not identify one engine design. Use the engine code and production period to choose ignition, filtration and induction components. For an aftermarket intake, compare sensor fittings, breather connections and service-filter requirements. Keep a record of the installed system so later replacement filters match it. Chassis and Lighting Choices Choose suspension components by generation, body, axle load and damper type. If an earlier owner lowered the car, identify the existing spring and damper combination before buying replacements. Replacement taillights and DRL modules need body-specific and headlamp-specific coverage. Confirm connectors and installation requirements alongside the desired appearance. Choose Your Part Identify engine and production p...

Find BMW 318is parts for a precise four-cylinder 3 Series build. Distinguish E30 and E36 applications before planning induction, chassis or brake work. Four-Cylinder Engine Applications The E30 318is uses BMW’s M42 four-cylinder engine. Later 318is applications need their own engine identification and production details before selecting internal or induction components. For an intake, compare airflow-meter connections, heat-shield mounting and filter access. A six-cylinder kit is not established as compatible simply because it uses the same chassis name. Brakes and Interior Fit Identify the calipers and rotor dimensions already fitted, especially on cars with brake conversions. Match hardware and pad shape to those assemblies. An A-pillar gauge pod needs the correct body and trim profile as well as the gauge diameter. Check attachment and visibility before planning additional instruments. Choose Your Part Separate E30 and E36 engine applications. Match intake connections and mounti...

Shop BMW 318ti parts for the 3 Series Compact. Its hatchback body and chassis application deserve their own checks when planning suspension, exhaust or brake service. Compact Body and Engine Details BMW’s E36 318ti Compact uses a four-cylinder engine, with displacement changing during production. Use engine identification and build details for filtration, ignition and engine-service parts. Choose an exhaust or rear-body component with Compact coverage. A sedan or coupe application does not establish routing and attachment for the hatchback. Brake and Suspension Service Match dampers and springs to the Compact chassis rather than a generic E36 description. Check mounting details, intended ride height and any axle conversion. For pads, hoses and hardware, identify the installed brake assembly and axle. If the car has been modified, record the donor components so future service parts follow the actual setup. Choose Your Part Identify Compact generation and engine. Use Compact-specific...

Shop BMW 323Ci parts for the E46 coupe or convertible, with the installed six-cylinder engine and body established before selecting induction, exhaust or suspension components. Intake and Engine Accessories E46 323 intake applications include Injen systems with particular engine and production coverage. Compare air-meter connections, filter placement and supplied mounting pieces. A crankshaft damper is a separate engine application. Match the engine family, pulley arrangement and manufacturer’s installation requirements rather than choosing by exterior diameter alone. Coupe and Convertible Chassis Work Choose exhaust and suspension components with the correct body coverage. Convertible weight and body structure make the permitted axle loads and application restrictions relevant. For brakes, identify the installed caliper, rotor dimensions and axle. Include sensors and mounting hardware in the service plan after reviewing the kit contents. Choose Your Part Identify coupe or converti...

Find BMW 323i parts by 3 Series generation and installed six-cylinder engine. Earlier and later cars require different induction, exhaust and chassis applications. Separate Engine Generations The 323i name spans more than one engine and chassis generation. Use engine identification to select intake connections, ignition specifications and engine-service components. For an intake kit, compare air-meter fittings, heat shielding and mounting. Review the exact engine coverage rather than extending an E36 kit to an E46 or later car. Body and Chassis Choices Choose lamps and exhaust components for the actual body. An E92 coupe lamp is not a general 323i lighting application. Brake conversions and earlier lowering work can change what is required. Record the installed calipers, rotor dimensions, springs and dampers before planning replacements. Choose Your Part Identify generation, body and engine. Compare intake connections and mounting. Select lamps and exhaust by exact body. Record bra...

Shop BMW 325Ci parts for the E46 coupe or convertible. Compare six-cylinder intake applications, body-specific chassis components and the equipment required for brake service. Intake Kit or Service Filter Injen E46 325 applications distinguish production coverage and kit configurations. Compare the air-meter connection, intake routing, heat shielding and supplied mounting pieces. A replacement filter must match the installed housing. Record the intake brand and model if the original airbox has been replaced. Coupe and Convertible Requirements Choose springs and dampers for the correct body and axle loads. Convertible applications should be confirmed rather than inferred from a coupe listing. For exhaust work, compare body routing, tip position and the original sections retained. For brakes, use the installed rotor and caliper to identify pads, sensors and hardware. Choose Your Part Identify coupe or convertible and production period. Compare intake routing and meter connections. Ma...

Choose BMW 325i parts by chassis generation, engine and body. The model spans different six-cylinder installations and body styles, with separate requirements for induction, trim and chassis work. Generation and Body-Specific Purchases Use the actual chassis and engine for intake, ignition and service components. E30, E46 and later applications should not be combined into one engine-parts assumption. Window visors and lamps need exact body coverage. Compare attachment method, door count and mounting surfaces before choosing an exterior accessory. Suspension and Brake Planning Identify factory or aftermarket springs and dampers before replacing individual pieces. Compatible travel, mount condition and alignment matter alongside ride height. For brakes, match rotor dimensions and pad shape to the installed caliper. Check sensors, clips and other fitting hardware separately from the friction parts. Choose Your Part Identify chassis, engine and body. Match accessories to door and windo...

Find BMW 325is parts with the car’s original market, generation and installed equipment established. This designation needs precise identification before choosing engine or chassis components. Market and Engine Identification Record the VIN-derived model, engine and production information. Regional 325is specifications and later modifications should be resolved before engine parts are selected. For induction work, identify the installed air-meter arrangement, housing and breather connections. A service filter and a complete intake kit are different purchases. Plan the Chassis Combination Choose suspension around the body, engine weight and existing mounts. Review spring and damper compatibility, wheel clearance and alignment together. Brake work should follow the actual calipers, rotors and hydraulic equipment. Keep conversion records so pads, hoses and hardware can be selected for the installed system. Choose Your Part Record market, generation and engine. Identify installed induc...

Explore BMW 325xi parts for the all-wheel-drive six-cylinder 3 Series. Establish generation and body before comparing engine accessories, suspension and service components. Identify the All-Wheel-Drive Generation Separate E46 and later 325xi applications. The all-wheel-drive system and chassis equipment must follow the actual generation, not just the xi suffix. For an intake or engine accessory, compare the exact engine, mounting and available clearance. A shared engine application does not establish every drivetrain-sensitive component. Sedan and Wagon Chassis Work Use all-wheel-drive suspension coverage and the correct body and axle loads. A wagon’s application should be confirmed separately from a sedan listing. For window accessories, identify body and door layout. For brake work, record rotor dimensions, caliper and axle before selecting sensors and hardware. Choose Your Part Identify AWD generation and engine. Separate sedan and wagon coverage. Match suspension axle loads and...

Choose BMW 328Ci parts for the E46 coupe and convertible. Focus on six-cylinder intake connections, engine accessory applications and body-specific suspension or exhaust requirements. Intake and Damper Applications Injen E46 328 intake selections have specific production and engine coverage. Compare the air-meter connection, inlet routing, filter position and supplied mounting pieces. For a crankshaft damper, establish exact engine-family coverage, pulley arrangement and installation procedure. Check any accompanying hardware requirements before scheduling the job. Body and Brake Configuration Coupe and convertible exhausts or suspension kits need their stated body coverage. Axle-load restrictions and existing lowering equipment affect the correct combination. Identify each axle’s caliper, rotor and pad shape before selecting brakes. Review sensors and hardware separately so the installation plan covers the full service. Choose Your Part Confirm E46 body and engine application. Com...

Explore BMW 328i parts by generation, engine and body. Earlier six-cylinder cars and later turbocharged four-cylinder applications need different induction, service and exhaust choices. Separate the Engine Applications Record the engine identification before choosing an intake, ignition component or service filter. A later turbocharged application should not be transferred to an earlier naturally aspirated engine. Compare air-meter fittings, breather connections, inlet routing and mounting. Where emissions equipment changes the application, use the manufacturer’s exact coverage. Plan Chassis and Exhaust Purchases Use sedan, coupe, convertible or wagon coverage for body-related components. An exhaust section must join the correct starting system and clear the actual bumper outlets. Select suspension by drivetrain and axle loads. Brake service needs its own caliper, rotor, pad-shape and sensor checks before comparing compounds or kit contents. Choose Your Part Identify generation, en...

Find BMW 328is parts for the E36 six-cylinder coupe. Compare intake system design, exhaust scope and chassis components for the equipment actually installed. E36 Intake Choices Injen E36 six-cylinder selections include heat-shielded intake configurations. Compare meter connections, shield mounting and filter access as well as the available finish. An E46 intake is a separate application. Establish the installed engine and inlet arrangement before choosing a kit or replacement element. Exhaust and Chassis Planning Decide whether you need a complete exhaust or a replacement section for an existing system. Coupe routing, mounting and tip clearance should be checked together. For suspension, compare spring and damper compatibility rather than ride height alone. Record any brake conversion before selecting pads, rotors and hydraulic parts. Choose Your Part Identify E36 coupe and engine. Compare meter connections and heat shielding. Review complete-system or section-only contents. Record...

Choose BMW 328xi parts for the all-wheel-drive six-cylinder 3 Series. Body, engine and emissions specification help distinguish the correct induction and chassis applications. Induction by Engine and Body Identify the actual engine and emissions equipment before comparing intake kits. A listing for an E92 coupe needs its exact engine and drivetrain coverage confirmed for the car being serviced. Compare meter connections, filter location and heat-shield mounting. A throttle controller is a separate pedal-interface device; verify its connector and application. All-Wheel-Drive Chassis Service Use xi-specific suspension coverage and the correct sedan, coupe or wagon application. Axle loads, damper type and front driveline clearance matter when changing ride height. Window accessories and exterior trim need exact body coverage. For brakes, identify the installed caliper, rotor dimensions and axle before choosing sensors or hardware. Choose Your Part Identify AWD chassis, engine and emis...

Shop BMW 330Ci parts for the E46 six-cylinder coupe or convertible. Plan engine-accessory and chassis work around the body and installed equipment. Engine Damper and Service Components Crankshaft damper applications identify the engine family and pulley arrangement. Compare the exact coverage and installation procedure, including required hardware, before scheduling replacement. For intake maintenance, identify the original airbox or installed aftermarket housing. Filter dimensions and connections should follow that assembly rather than a general E46 description. Body-Specific Chassis Requirements Springs and dampers need coupe or convertible coverage and appropriate axle-load limits. Compare compatible travel and mount condition alongside the desired ride height. Choose brake pads by caliper and rotor equipment, then compare compound use. Confirm the sensor connector and fitting hardware separately from the friction parts. Choose Your Part Identify E46 body and engine. Check dampe...

Shop BMW 330i parts by engine generation and body. Earlier six-cylinder cars and later turbocharged four-cylinder models need separate intake, exhaust and service applications. Exhaust Scope and Engine Coverage G2X AWE Touring selections include axle-back exhaust applications with specific production coverage. An axle-back changes the rear portion; compare retained pipework and the exact sections supplied. Check tip finish, bumper-outlet arrangement and mounting before deciding on appearance. An earlier 330i body or engine is a different exhaust application. Intake and Chassis Planning For induction components, compare engine identification, sensor connections and breather fittings. Record the housing if an aftermarket intake is already installed. Select springs and dampers by body, drivetrain and axle loads. Brake components need the installed rotor and caliper application before pad compound and sensor choices are made. Choose Your Part Identify engine, chassis and body. Compare ...

Choose BMW 330xi parts by all-wheel-drive generation, engine and body. Induction, suspension and exterior accessories each need their own application details. Engine and Induction Requirements Identify the actual six-cylinder engine and installed intake before choosing service filters or induction hardware. Compare sensor fittings, breather connections and mounting clearance. For a pedal controller, confirm the exact accelerator connector and supported vehicle application. Its response adjustment serves a different purpose from an intake or engine calibration. AWD Chassis and Body Accessories Use xi-specific spring and damper coverage, body and axle-load limits. An earlier or later all-wheel-drive generation should not be treated as the same chassis application. Window visors and trim depend on door and window layout. Brake pads, rotors and sensors should instead follow the installed caliper, axle and electrical connection. Choose Your Part Identify AWD generation, engine and body....

Shop BMW 335d parts for the six-cylinder diesel 3 Series. Separate engine generation and drivetrain before planning brake service, charge-air or chassis work. Diesel Engine and Charge-Air Details The U.S. E90 335d uses a 3.0-liter six-cylinder diesel. Induction and cooling purchases need the specific diesel engine and system connections, not petrol 335i coverage. Compare charge-air couplings, sensor ports and mounting for the exact installation. Keep existing engine and emissions equipment documented when choosing service components. Rotors and Lighting Equipment Hawk Talon front-rotor applications identify the E90 335d separately. Match axle, rotor diameter, thickness and height to the installed caliper before comparing surface designs. DRL modules need their stated chassis, headlamp and production coverage. A later 3 Series module is not established as suitable for an E90 simply by sharing the brand. Choose Your Part Identify diesel engine generation and drivetrain. Match charge-...

Find BMW 335i parts by engine generation, body and current build specification. N54 and N55 induction, charge-air and exhaust applications need separate consideration. Identify N54 or N55 Use engine identification to distinguish the twin-turbo N54 from the later N55 installation. Intake connections and charge-air hardware should follow that engine application. Record existing intake, charge pipe, intercooler and calibration changes before choosing companion components. For ignition service, use the required plug specification and any documented tuner requirements. Choose the System You Need Compare a complete exhaust with an axle-back, mid-pipe or conversion section. Check body routing, joining points, valve operation and the pieces retained from the existing system. For chassis work, match suspension and brakes to the actual body and drivetrain. Identify calipers and rotor material before comparing pad compounds or sensor kits. Choose Your Part Identify engine, body and drivetrain...

Shop BMW 335is parts for the N54-powered E92 coupe or E93 convertible. Distinguish its engine, transmission and cooling equipment before planning upgrades. N54 and Transmission Details BMW retained the twin-turbo N54 in the 335is. Do not transfer a later 335i N55 intake or charge-air application without explicit 335is coverage. Identify manual or dual-clutch transmission when choosing driveline components. Review the complete assembly and installation requirements rather than selecting by engine alone. Cooling and Body Configuration The 335is has enhanced cooling equipment. Identify the circuit and original component before choosing a radiator, oil-cooling component, hose or related upgrade. Exhaust and suspension choices need coupe or convertible coverage. Compare valve operation, pipe sections, axle loads and mount condition as part of the installation plan. Choose Your Part Confirm N54 and E92 or E93 body. Identify manual or dual-clutch transmission. Record installed cooling cir...

Find BMW 335xi parts for the turbocharged all-wheel-drive 3 Series. Match the exact engine and body before choosing induction or drivetrain-sensitive components. Twin-Turbo Induction Applications For an N54 installation, compare the complete inlet arrangement, meter or sensor provisions, heat shielding and mounting. A twin-inlet kit has a different application from a later single-inlet design. Use the kit’s stated body and production coverage. A coupe listing needs explicit confirmation for another body or the xi drivetrain. AWD Chassis and Controls Select suspension with xi coverage and correct axle loads. Review front-axle clearance and the manufacturer’s permitted lowering and alignment requirements. For a pedal controller, verify the accelerator connector and supported vehicle. Response adjustment is separate from increasing engine output or changing the engine calibration. Choose Your Part Identify engine, body and xi drivetrain. Compare twin-inlet connections and mounting. Ch...

Explore BMW 525i parts by six-cylinder engine generation, body and equipment. Intake service, brake work and chassis changes should follow the assemblies fitted to the car. Engine Service and Induction Use engine and production identification for ignition, filtration and induction components. A component from another 525i generation is not confirmed by model name alone. For an aftermarket intake, compare meter or sensor fittings, breather connections and filter-service access. Keep the housing reference for future replacement elements. Body and Chassis Planning Select suspension for sedan or Touring body, drivetrain, axle loads and rear-system arrangement. Existing lowering should be documented before individual springs or dampers are replaced. For brakes, record caliper, rotor dimensions and axle. Review pad compound, sensors and fitting hardware after establishing the correct assembly application. Choose Your Part Identify engine generation and body. Match intake fittings and ser...

Find BMW 525xi parts for the all-wheel-drive petrol 5 Series. Engine, body and chassis generation are the starting points for service and suspension purchases. Engine and Drivetrain Interfaces Use the exact engine for ignition, filters and induction components. Compare sensors, breathers and housing references for the installed assembly. AWD-sensitive parts require separate mounting and clearance checks. Engine-family similarity does not establish sump, front-axle or exhaust-routing compatibility. Chassis and Brake Configuration Choose springs and dampers with xi, body and axle-load coverage. Record electronic-damper or rear-system equipment before considering a kit. Select brakes by caliper, rotor dimensions and axle, then check pad compound, wear sensors and hardware contents. Keep conversion references for later service. Choose Your Part Identify petrol engine, generation and body. Compare induction and service interfaces. Require xi chassis coverage and clearance. Record brakes...

Explore BMW 528e parts for the E28 eta-powered six-cylinder. Use the actual engine build and installed chassis equipment when planning restoration or routine service. Eta Engine Service The 528e belongs to BMW’s eta engine family, developed around torque and economy. Engine-service components should follow its actual engine application rather than the 528i designation. For an engine rebuild or later conversion, record block, head, management and ignition details. Bearings and internal parts require measured build specifications, including prior machining. Classic Chassis and Brakes Inspect suspension mounts and bushings alongside dampers. Decide whether the project calls for original ride height or a compatible lowering setup before choosing springs. Brake parts must match the installed calipers, rotor or drum dimensions and hydraulic fittings. Preserve any not-for-street-use restriction when comparing competition compounds. Choose Your Part Identify eta engine and build configurat...

Find BMW 528i parts by engine generation, body and installed equipment. Earlier six-cylinder cars and later turbocharged four-cylinder applications need different induction and service components. Identify the Actual Petrol Engine BMW introduced a turbocharged 2.0-liter four-cylinder in the U.S. 2012 528i. Do not transfer an earlier six-cylinder intake or ignition application to that engine. Match filters, sensor fittings, breathers and inlet connections to the installed system. A pedal controller has a separate accelerator-connector application and does not establish a horsepower increase. Chassis and Brake Service Choose suspension by body, drivetrain, axle loads and damper equipment. Record earlier lowering or rear-system changes before replacing individual components. Brake pads need the installed caliper, axle, pad shape and rotor material. Compare intended use and sensor or hardware contents after confirming the assembly application. Choose Your Part Identify engine and produ...

Explore BMW 530i parts by engine generation and body. Earlier six-cylinder and later turbocharged applications need separate engine-service and induction coverage. Engine and Service Components Use engine identification and production details before choosing intake or ignition hardware. The 530i designation is not one universal engine application. Match filters to the original airbox or the installed aftermarket housing. Sensor fittings, breathers and inlet connections should follow the actual assembly. Headlamp and Chassis Equipment DRL modules must match headlamp technology, production period and connector. A related M5 styling description does not prove compatibility with every 530i lamp. For suspension and brake work, record body, drivetrain, damper type, axle loads, calipers and rotors. Compare each component’s application and installation contents. Choose Your Part Identify engine and generation. Match intake housing and connections. Record headlamp module and connector. Iden...

Find BMW 530xi parts for the all-wheel-drive petrol 5 Series. Exact brake applications and xi-specific chassis coverage are useful starting points for service or a build. Brake Applications and Intended Use Identify caliper, rotor material, pad shape and axle before selecting a compound. A pad listed for another BMW requires confirmed cross-coverage. Competition compounds have specific temperature and bedding requirements. Choose the manufacturer’s intended use rather than treating every race pad as a road replacement. Engine and AWD Chassis Use actual engine identification for ignition, filters and induction components. Compare housing references, sensors and connection details. Choose suspension with xi, body and axle-load coverage. Record electronic dampers and any rear-system or earlier lowering changes before replacing parts. Choose Your Part Identify brake assemblies by axle. Compare pad use and operating requirements. Record engine and installed service equipment. Require xi...

Explore BMW 535i parts by engine generation and body. Classic naturally aspirated applications and later turbocharged cars need separate intake, service and chassis coverage. Engine Identity Before Induction Use actual engine identification before comparing intake or charge-air components. Earlier classic engines, N54 and N55 applications should not be combined into one installation assumption. For a turbocharged build, record current intake, charge pipe, intercooler and calibration details. Match sensor fittings, couplings and mounting with the installed setup. Exhaust and Chassis Scope Compare exhausts by body, joining points, valves and the exact sections supplied. A conversion component should identify the starting system it requires. For suspension and brake service, record body, drivetrain, axle loads, calipers and rotors. Existing conversions can change the required replacement parts. Choose Your Part Identify engine generation and body. Record induction and calibration chan...

Find BMW 535is parts with the classic chassis, market and installed six-cylinder identified. Restoration and chassis service should follow the actual assemblies on the car. Engine and Restoration Records Record injection, ignition, gearbox and engine references before buying service components. Later engine or management conversions need their own installed-component documentation. For intake or exhaust work, compare original mounting, connections and clearances. A sports designation does not establish a universal modern upgrade application. Chassis Condition and Brake Use Inspect mounts, bushings and dampers together before choosing a suspension change. Document existing springs and brake conversions. Select brake pads by installed caliper, rotor material, axle and pad shape. Competition compounds need the manufacturer’s intended-use and operating guidance retained. Choose Your Part Identify chassis, market and engine. Document original or converted engine equipment. Inspect suspe...

Find BMW 535xi parts for the turbocharged AWD 5 Series. Compare engine-specific induction and xi chassis applications before choosing upgrades or service components. Twin-Intake Kit Selection Injen E60 twin-intake applications identify a particular engine and production range. Compare both inlet connections, filter requirements, shielding and mounting. Require explicit coverage for the actual xi body and installation. A later single-inlet engine application is a separate purchase decision. AWD Chassis and Service Equipment Choose suspension with xi, body and axle-load coverage. Record electronic dampers or rear-system equipment and review front-driveline clearance. For brakes, identify caliper, rotor dimensions and axle. Compare pads, sensors and hardware contents separately so the service plan covers the installed assembly. Choose Your Part Identify engine, E60 application and body. Compare both intake connections and filters. Require xi suspension and clearance coverage. Record b...

Explore BMW 540i parts by engine generation and body. Earlier V8-powered cars and later turbocharged six-cylinder models need entirely different induction and service applications. V8 or Six-Cylinder Application Identify the actual engine before choosing intake, ignition, cooling or filter components. A shared 540i name does not establish the engine’s layout or connections. For an aftermarket housing or modified cooling system, retain installed references. Service parts should match the assembly fitted rather than the car’s original specification alone. Lighting and Chassis Options DRL modules need the exact headlamp technology, module, connector and production coverage. Similar styling does not settle the electrical application. Choose suspension by body, drivetrain, axle loads and damper equipment. Brake parts need caliper, rotor and axle identification before compound or kit contents are compared. Choose Your Part Identify V8 or six-cylinder engine generation. Record installed i...

Find BMW 545i parts for the V8-powered E60-era 5 Series. Establish engine, gearbox and body before choosing induction, service or chassis components. V8 Service and Induction BMW introduced the 545i with a 4.4-liter V8 using Valvetronic. Intake, ignition and cooling components need exact engine and production coverage. Identify the installed airbox or aftermarket housing before choosing filters. A pedal controller has its own accelerator-interface application and does not establish an engine-output gain. Transmission and Chassis Details Record the actual gearbox before choosing driveline or mounting components. Engine matching alone does not resolve the transmission-side interface. Suspension and brakes need body, axle loads, damper type, caliper and rotor details. Review kit contents and any electronic-control requirements before planning installation. Choose Your Part Identify V8 engine, production period and body. Match intake housing and service references. Record transmission ...

Find BMW 550i parts by V8 engine generation and body. Earlier naturally aspirated and later turbocharged applications need separate induction, ignition and cooling coverage. Identify the V8 Installation Use engine and production identification before selecting service components. The 550i designation spans different V8 layouts and cannot establish every connection or mounting. Record installed intake, cooling, exhaust and calibration changes. Replacement filters and hoses should follow the actual housing or system fitted. Chassis and Exhaust Scope Compare exhausts by body, drivetrain, supplied sections and starting-system requirements. A sedan application does not establish Gran Turismo routing. Suspension and brakes need the actual body, axle loads, damper equipment, calipers and rotors. Review sensors and fitting hardware separately from friction-part choices. Choose Your Part Identify V8 generation and body. Record existing engine-system changes. Compare exhaust scope and routin...

Shop BMW 645Ci parts for the 4.4-liter V8 coupe or convertible. Engine, gearbox and body identification guide induction service and chassis selection. V8 Service and Induction BMW’s 645Ci uses a 4.4-liter V8 application. Match ignition, filters and cooling components to exact engine and production coverage. For an aftermarket intake, identify the housing and service-filter reference. A pedal controller needs its own accelerator-connector coverage and does not establish additional engine horsepower. Coupe and Convertible Equipment Suspension and exhaust components need the actual body application. Compare axle loads, routing, mounting and any electronic-damper requirements. Record the gearbox before choosing driveline or mounting components. Brake service needs caliper, rotor dimensions and axle identification separately. Choose Your Part Identify V8 engine and production details. Record coupe or convertible and gearbox. Match intake and pedal interfaces. Check chassis and brake equ...

Choose BMW 650i parts by V8 generation and body. Earlier naturally aspirated and later turbocharged engine applications need separate intake, ignition and cooling coverage. V8 Engine and Body Identification Record engine and production details before selecting service components. Coupe, convertible and Gran Coupe body applications should be identified separately. Match replacement filters and hoses to the housing or system installed. For a modified car, retain intake, cooling and calibration references. Rotor and Pad Kit Selection Compare rotor dimensions, material, mounting and axle with the installed caliper. Confirm the kit’s exact application before evaluating drilled, slotted or other surface designs. Pad compound needs appropriate road or competition coverage and the manufacturer’s bedding guidance. Check wear sensors and fitting-hardware contents separately. Choose Your Part Identify V8 generation and exact body. Record installed intake and cooling assemblies. Match rotors a...

Explore BMW 733i parts for classic 7 Series service and restoration. Use installed six-cylinder engine equipment and chassis references before choosing replacement components. Classic Engine Service Record injection, ignition, gearbox and production details. Related classic BMW engines require confirmed component cross-references rather than assumed interchangeability. For filtration and seals, identify the actual housing or assembly and specified material. Keep records of conversions or substituted components from earlier restoration work. Suspension and Hydraulic Condition Inspect dampers, mounts, bushings, boots and bump stops together. Select a compatible spring and damper combination for restoration ride height or the intended lowering. Brake hoses and friction parts need the installed caliper, rotor or drum dimensions, axle and hydraulic fittings. Document any conversion before ordering service parts. Choose Your Part Identify classic chassis and engine equipment. Record serv...

Shop BMW 735i parts by 7 Series generation and engine configuration. Classic six-cylinder and later V8 applications need separate induction, service and chassis coverage. Engine Generation and Service Interfaces Identify the engine before choosing intake, ignition, filters or cooling components. BMW’s later 735i applications include V8 engines; the badge does not establish one layout. Compare installed housings, sensor fittings, connections and mounting. Record engine or management changes before selecting companion components. Brake and Suspension Equipment Choose brakes from the actual caliper, rotor dimensions, axle and pad shape. A related-model listing requires confirmed cross-coverage. Suspension must match chassis, engine, body, axle loads and damper or rear-system equipment. Inspect mounts and bushes alongside replacement dampers. Choose Your Part Identify engine configuration and generation. Match installed service interfaces. Confirm brake application by assembly. Review ...

Choose BMW 735iL parts for the long-wheelbase 7 Series with the exact engine and chassis identified. Brake equipment and long-body suspension coverage guide a complete service plan. Long-Body Engine Identification Record chassis, production, original market and installed engine details. The 735 family spans different engine applications, and body length alone does not settle service-part fit. Match filters, ignition and cooling components to the assemblies fitted. Retain references for any replacement engine or earlier restoration changes. Brakes and Suspension Scope Identify caliper, rotor dimensions, axle and pad shape before comparing compounds. Related-model pads need confirmed cross-coverage with the actual brake system. Choose suspension with engine, long-wheelbase body, axle-load and rear-system coverage. Review which original components a kit retains or replaces. Choose Your Part Identify long-body chassis and engine. Record installed service assemblies. Confirm brakes befo...

Explore BMW 740i parts by engine generation and body. Earlier V8 and later turbocharged six-cylinder applications require different induction and service references. Identify V8 or Six-Cylinder Use engine and production identification before selecting filters, ignition, intake or cooling components. A shared 740i name does not establish the engine layout. Record original or aftermarket housings and any cooling or management changes. Service elements should follow the assemblies installed. Lighting and Chassis Options DRL modules must match the actual headlamp, module number, connector and production coverage. A model-year range is only part of the electrical application. Choose suspension and brakes using body, drivetrain, axle loads, damper equipment, calipers and rotors. Review sensors and hardware separately from friction parts. Choose Your Part Identify engine generation and exact body. Record installed service assemblies. Match headlamp modules and connections. Check chassis a...

Find BMW 740iL parts for the long-wheelbase V8 7 Series. Engine generation, production details and rear-system equipment matter for service and chassis work. V8 Service and Long-Body Details Identify the actual V8, gearbox and production period before selecting ignition, filters, induction or cooling components. Related generations need separate references. For exhaust and body-sensitive parts, use long-wheelbase routing and mounting coverage. Standard-body dimensions should not be assumed suitable where length affects the component. Suspension and Brake Equipment Record the rear spring or level-control arrangement and damper equipment. Choose components with long-body, engine and axle-load coverage. Match brake pads, rotors and hoses to the installed caliper, axle and hydraulic fittings. Document conversions and substituted assemblies for future maintenance. Choose Your Part Identify V8 generation, gearbox and production. Require long-body routing and mounting coverage. Record rea...

Shop BMW 750iL parts for the classic long-wheelbase V12 7 Series. Engine generation, installed systems and body-sensitive chassis details guide restoration and maintenance. V12 Service and Restoration References Identify the actual engine, injection, ignition and gearbox before selecting components. Related V12 generations still need their own service references. For restored or modified cars, document installed housings, management and cooling equipment. Universal performance-system wording does not establish compatibility with the V12 installation. Long-Body Chassis Coverage Use long-wheelbase and engine-specific coverage for suspension axle loads and rear-system equipment. Inspect mounts and bushes alongside dampers. Exhaust and underbody components must match long-body routing and mounting. Brake parts should follow the installed caliper, rotor, axle and hydraulic fittings. Choose Your Part Identify V12 generation and installed systems. Document restoration and management chang...

Find BMW 840Ci parts for the classic E31 V8 coupe. Engine version, gearbox and restoration history guide service and chassis component selection. V8 Service and Build Details Identify the installed engine and production period before choosing ignition, filters, induction or cooling parts. Related V8 applications still need exact component coverage. Document engine, management and driveline changes made during restoration. Universal performance-system wording does not establish compatibility with the car’s controls or installation. Suspension and Brake Restoration Inspect dampers, mounts, bushes, boots and bump stops together. Choose original ride height or a compatible lowering setup before selecting springs. Brake parts need the installed caliper, rotor dimensions, axle and hydraulic fittings. Record conversions so future pads, hoses and hardware follow the actual assemblies. Choose Your Part Identify E31 V8 version and gearbox. Document restoration and management changes. Inspect...

Choose BMW 850Ci parts for the classic E31 V12 coupe. Engine version and production details matter when planning brake service, suspension restoration or engine work. V12 Identification and Restoration Record the installed V12, gearbox and production date. Changes within the E31 range make the actual engine and component reference more useful than the 850Ci badge alone. For an aftermarket engine system, review its required fuel, ignition and management interfaces. A universal kit designation does not establish a complete installation for an E31 V12. Brake and Suspension Service Choose pads and hardware by installed caliper, axle and rotor specification. Cross-model product titles need confirmed manufacturer application coverage. Inspect strut boots, bump stops, mounts and bushes with the dampers. Replace damaged protective components while access is available, using the correct dimensions and attachment method. Choose Your Part Record V12 version, gearbox and production. Document p...

Find BMW 850i parts for the classic E31 V12 coupe. Build a service plan around the installed engine, gearbox, brake assemblies and restoration history. V12 Engine and Installation Details Use engine and production identification for filtration, ignition, induction and cooling components. Keep references for replaced housings, sensors and other assemblies. Universal engine accessories need an installation plan covering fuel, ignition and control interfaces. Check the exact system requirements before combining components. Restore Brakes and Damper Protection Brake pads follow caliper, axle, rotor and pad shape. Confirm any shared application against the manufacturer’s fitment information rather than relying on another model’s title. Check boots, bump stops, mounts and bushes when servicing dampers. Match protective parts to the installed assemblies, including any previous suspension conversion. Choose Your Part Identify E31 V12 and gearbox. Record engine and control-system changes. C...

Find BMW M3 parts by generation, engine and body. Modern F8X and G8X intake or exhaust applications should be matched precisely before comparing sound, appearance and installation scope. Induction and Exhaust by Generation Match intake housings, turbo-inlet connections and sensor provisions to the exact engine. Shared M3/M4 coverage still needs the correct generation and installation details. Compare full exhaust systems with mid-pipes and conversion sections. Review resonation, valve operation, tips and the compatible starting exhaust for each configuration. Body and Brake Equipment Exterior components need the actual sedan, coupe, convertible or Touring application where relevant. Compare mounting and required original trim rather than transferring one body’s spoiler application. Brake pads and rotors follow the installed caliper, dimensions, material and axle. Confirm iron or carbon-ceramic equipment before selecting friction components or a conversion. Choose Your Part Identify...

Explore BMW M5 parts by chassis, engine and body. Earlier petrol generations, F90 AWD and the newer plug-in hybrid need distinct exhaust, induction and chassis applications. Exhaust Configuration by Generation Select exact chassis and sedan or Touring coverage before comparing exhaust sound. F90 systems and G90/G99 hybrid systems have different installation applications. Compare complete cat-back systems with mid-pipes and conversion pieces. Review valve operation, resonation, tips and original components retained for the actual system. Powertrain and Lighting Equipment The M5 name spans different engine layouts, including V10, V8 and later V8 plug-in hybrid versions. Match induction, cooling and service parts to the actual powertrain. DRL modules require original lamp technology, connector, module and production coverage. Brake and suspension purchases also need the installed equipment and exact drivetrain application. Choose Your Part Identify chassis, powertrain and body. Compar...

Explore BMW M6 parts by generation, engine and body. Classic and later M6 applications require separate powertrain, brake and chassis references. Generation and Control Interfaces Record chassis, engine, gearbox and coupe, convertible or Gran Coupe body before selecting components. A shared M6 name does not identify every installation. A pedal-response controller requires the correct accelerator connector and vehicle application. It changes response behavior rather than establishing a verified engine-output increase. Brake Application Before Compound Match caliper, rotor dimensions and material, pad shape and axle. Confirm shared M5/M6 coverage against the exact installed brake system. Compare street and competition compounds by their intended conditions. Review sensors and hardware separately, and retain conversion references where the original brakes have changed. Choose Your Part Identify generation, engine and body. Match accelerator-control interfaces. Record calipers and roto...

Choose BMW X1 parts by chassis generation, engine and sDrive or xDrive configuration. Brake and accessory applications vary across the model’s different layouts. Brake Dimensions and Connections Record rotor diameter, thickness, caliper and pad shape for each axle. A 335 mm rotor listing applies only where the actual brake assembly and manufacturer coverage match. Brake hoses and wear sensors also need correct length, routing and connections. Confirm shared BMW or Mini applications against the installed assembly. Engine Accessories and Chassis Generation Match engine accessories to the actual engine, management and connections. Separate a complete injection system from a plate or conversion component requiring an existing setup. Suspension coverage needs exact generation, drivetrain, axle loads and damper equipment. An sDrive or xDrive badge without chassis information does not settle every mounting or clearance requirement. Choose Your Part Identify chassis, engine and drivetrain....

Find BMW Z3 parts with engine, body and production details recorded. Roadster, coupe and M applications need distinct references for engine and chassis service. Engine and Damper Interfaces Match a crankshaft damper to the installed engine, crank mounting and accessory-drive arrangement. A six-cylinder family label does not establish every Z3 application. Universal engine accessories need their own installation plan covering fuel, ignition and management interfaces. Document engine conversions before selecting related-model service parts. Brake and Body Equipment Choose rotors by caliper, axle, dimensions, material and side. Confirm shared E36 or other BMW coverage against the actual brake assembly. Body-sensitive trim, exhaust and chassis parts need roadster or coupe coverage. Match mats to measured floor shape and retention requirements rather than another vehicle’s product title. Choose Your Part Identify engine, body and M or standard application. Match crank damper and accesso...

Explore BMW Z4 parts by generation, engine and transmission. Crankshaft dampers and pedal-control accessories need exact application details rather than a shared roadster badge. Crank Damper Specification Compare engine, crank mounting, accessory grooves, pulley dimensions and any stated underdrive or overdrive configuration. Review dry-sump or other build-specific requirements before selecting a damper. Shared Supra/B58 coverage needs the correct engine version and installation. Earlier Z4 engines and unrelated damper families require separate references. Pedal Interfaces and Chassis Details A pedal-response controller must match the vehicle’s accelerator connection and application. It changes response behavior rather than establishing a verified engine-output gain. Brake and suspension parts need generation, engine, caliper or damper equipment and axle-load coverage. Record body and gearbox where routing or installation depends on them. Choose Your Part Identify generation, engin...

Shop H&R lowering springs, lift springs, coilovers, sway bars, suspension components, Trak+ wheel spacers, adapters, bolts, studs, and lug nuts by exact manufacturer part number and verified application.Choose Your Part Match the exact H&R manufacturer part number and package quantity Confirm year, make, model, trim, drivetrain, axle load, body style, and factory suspension Check the stated ride-height range and required shock or electronic-damper provisions Match wheel adapters by both bolt patterns, both center bores, thickness, thread pitch, attachment method, and supplied hardware Verify wheel hardware length, diameter, thread pitch, seat type, engagement, and clearance Related Collections H&R products Lowering springs Coilovers Sway bars Frequently Asked QuestionsHow do I confirm an H&R suspension part fits my vehicle?Match the exact part number and exact year, make, and model, then confirm trim, drivetrain, axle load, body style, factory suspension, electronic ...

Wheel spacers and wheel adapters for cars, trucks, and SUVs are stocked at Black Ops Auto Works. Shop hub centric wheel spacers, bolt on and slip on spacers, wheel adapters that change bolt pattern, and forged aluminum spacers ranging from 5mm to 2 inch thickness for BMW, Audi, Volkswagen, Porsche, Subaru, Toyota, Ford, and Chevrolet platforms from Spidertrax, Motorsport Tech, ECS Tuning, and Black Ops Auto Works. Every wheel spacer and adapter is filterable by year, make, model, trim, bolt pattern, and hub bore so the correct thickness, offset change, and stud or bolt pattern ships the first time. Black Ops Auto Works carries 643 wheel spacer and adapter SKUs across bolt on, slip on, and adapter categories. What This Collection Covers Wheel spacers move the wheel outward from the hub to correct fitment issues like brake caliper clearance, fender clearance for wider tires, or a wider, more aggressive stance. Wheel adapters go a step further and change the bolt pattern entirely, ...

Shop aftermarket wheels, tires, lug nuts, wheel spacers, hub rings, TPMS sensors, valve stems, and wheel accessories at Black Ops Auto Works. Find performance wheels and tires for street cars, trucks, SUVs, muscle cars, imports, off-road vehicles, and custom builds from trusted automotive brands. Aftermarket Wheels for Cars, Trucks, and SUVs Choose cast, flow-formed, forged, replica, off-road, and performance wheels in a wide range of diameters, widths, offsets, finishes, bolt patterns, and center bores. Our selection supports applications from daily-driven vehicles and sports cars to lifted trucks, SUVs, drift builds, and track vehicles. Performance Tires for Street, Track, and Off-Road Use Shop tires for summer performance, all-season driving, winter conditions, touring, towing, off-road terrain, and high-performance applications. Match tire size, load rating, speed rating, tread design, compound, and seasonal use to the vehicle and driving conditions. Wheel Fitment, Offset, and ...