Sold out
Fuel Injector Connection FIC1600DENSO fuel injector
Click to zoom in
View vehicle applications

Description

Build the fuel system around the correct flow and connection

Fuel Injector Connection FIC1600DENSO supports the stated flow, fuel, electrical, and physical configuration. Injectors are sold Individually

Features

  • Injectors are sold Individually
  • fitment for over 300 different applications in stock.
  • The tests were performed at varying temperatures to achieve realistic results. Linear tuning with excellent low-end, and idle rpm.

Fitment & Requirements

Scope Requirement
Component-specific application Electrical connector type: U.S. CAR
Component-specific application o ring to o ring length 60mm
Component-specific application top and bottom o rings are for the application you select

Part Numbers & Options

Option Manufacturer Part Number
Default FIC1600DENSO

Specifications

Detail Value
Product Type Fuel Injector
Electrical RATED FOR ALL-FUEL TYPES, HIGH IMPEDANCE - MATCHED SET
Flow Rating FLOW CHART
Flow Rating 2 Each set is sold with a complete flow-data chart indicating individual static flow rates at 3.0, 3.5, and 4.0 BAR. As well as 3.0 BAR dynamic pulse testing for idle (15% duty-cycle) and 50% duty-cycle. Along with a complete dead time off-set (latency) table. Flow matching was done with industry-standard equipment of the highest quality.
Fuel Compatibility SPECIAL NOTE TO OUR E85 USERS
Fuel Compatibility 2 Ethanol tends to "dry" the orifices. Customers should be made aware that this can be a problem with some fuel injectors. And may cause a "sticking" problem. It is suggested that a tank of 91-98 octane gasoline be run to every 5 or 6 tanks of Ethanol to re-lube not only the fuel injectors, but the entire fuel component system. This is also considered to be good maintenance, but not essential, for stainless steel based fuel injectors.
Electrical 2 Electrical connector type: U.S. CAR
Dimensions o ring to o ring length 60mm
Application Requirement top and bottom o rings are for the application you select

What's Included

  • The exact selected product or set shown in the Part Numbers & Options table
  • Unlisted injectors, rails, wiring, fittings, tuning, tools, and installation hardware are not included

About Fuel Injector Connection

Fuel Injector Connection supplies flow-matched fuel injectors, connection components, service parts, and supporting fuel-system hardware. Correct selection depends on the exact flow, electrical, dimensional, spray-pattern, quantity, and engine requirements rather than a similar-looking injector alone.

Related Parts

  • No external product is linked. Verify any injector adapters, rails, seals, pumps, or tuning components against an ACTIVE Black Ops Auto Works listing for the exact application before purchase.

FAQ

What is the FIC1600DENSO?

It is the exact fuel injector and configuration described in the fitment and specification sections above.

Is this selected by vehicle model alone?

No. Confirm every stated engine, connector, rail, length, flow, and package requirement that applies to this exact item.

Is tuning required?

Fuel-system and injector changes can require calibration. Use qualified tuning guidance for the exact engine, fuel, injector data, and operating pressure.

Does the listing include every surrounding fuel-system part?

No. Only the components stated in the What's Included section are included.

Can a related part number be substituted?

No. A different flow rate, length, connector, spray pattern, quantity, or adapter package is a different configuration.

Which fuel can be used?

Use only the fuels explicitly listed in the specifications and current manufacturer data for this exact configuration.

What should be checked before installation?

Verify the part label, seals, connector, rail fit, quantity, fuel compatibility, and calibration requirements before opening the fuel system.

Who should install fuel-system components?

A qualified technician should depressurize the system, follow the vehicle service procedure, prevent contamination, and leak-check the completed installation.

Installation Instructions

  1. Confirm the Fuel Injector Connection part label and every fitment, connector, dimension, flow, quantity, and fuel requirement before installation.
  2. Review the vehicle, engine, or component service procedure and disconnect electrical power where required.
  3. Relieve fuel-system pressure safely and work in a ventilated area away from sparks, flame, and hot surfaces.
  4. Keep all ports and components clean, replace only the seals specified for the exact application, and do not force mismatched connectors or fittings.
  5. Install the component in the documented orientation and tighten fasteners or fittings to the applicable current specification.
  6. Restore pressure, inspect every disturbed connection for leaks, confirm normal operation, and complete any required calibration before road use.

Fuel Injector Connection 1600 CC Denso Fuel Injector for Imports

FIC1600DENSO
Fuel Injectors
Same Day or Next Business Day
$ 133.00

Military & First Responders

Military & First Responders

A program for military members and first responders, with dedicated verification and support for your next build.

Learn More & Apply

Your cart

×