View vehicle applications
Fitment notes and restrictions
Description
Increase inlet area while keeping the turbo response clean and predictable
AWE Tuning 2660-15118 replaces the supported GR Supra factory airbox with a 4.5-inch carbon-fiber inlet and a large oil-less inverted-cone filter. AWE reports a 71 percent increase in filter surface area over stock and dyno-tested gains of up to 15 wheel horsepower and 21 lb-ft on its Stage 1 test vehicle.
Key Features
- AWE Tuning 2660-15118 is matched to the verified application and configuration
- 4.5-inch-diameter carbon-fiber inlet tube
- Oil-less inverted-cone filter with 71 percent more surface area than the factory filter
- CNC laser-cut aluminum support bracket with machined mounting points
- Machined aluminum sensor fitting for an OE-style connection
- AWE reports up to 15 wheel horsepower and 21 lb-ft on a Stage 1 test vehicle
- No ECU calibration required when installed and used as intended
- AWE fitment and no-check-engine-light guarantees under current terms
Application details and restrictions
| Years | Make | Model | Requirements |
|---|---|---|---|
| 2020-2026 | Toyota | GR Supra | Verified AWE S-FLO application. Confirm the exact model year and original intake configuration before ordering. |
Specifications
| Detail | Value |
|---|---|
| Manufacturer Part Number | 2660-15118 |
| Product Type | S-FLO carbon-fiber intake system |
| Inlet Diameter | 4.5 in |
| Filter | Oil-less inverted-cone filter |
| Filter Surface Increase | 71 percent over stock, as reported by AWE |
| Construction | 2x2 twill carbon-fiber inlet with aluminum support bracket |
| ECU Tune | Not required when installed and used as intended |
| Emissions Status | 50-state legal; does not tamper with emissions controls |
| UPC | 850092394057 |
What's Included
- One exact AWE Tuning 2660-15118 S-FLO carbon-fiber intake tube
- Oil-less filter
- CNC laser-cut support bracket
- Couplers, clamps, and installation hardware supplied by AWE
About AWE Tuning
AWE develops application-specific intake and exhaust systems around measured airflow, sound, packaging, and installation requirements. Its fitment and no-check-engine-light guarantees apply under AWE's current terms when the product is installed correctly and used in the intended configuration.
Related Parts
- The optional AWE carbon intake lid is a separate product and must match the same GR Supra intake system; no unverified internal product link is included.
FAQ
What is the 2660-15118?It is cold air intake for the verified 2020-2026 Toyota GR Supra applications listed above.
What application must be confirmed before ordering?Confirm the exact GR Supra model year, factory intake layout, sensor connection, and supplied AWE hardware before installation.
What is included?The exact supplied components are listed in the What's Included section; unrelated installation parts are not included.
Is this a universal product?No broad universal fit is claimed. Use only the verified vehicle, dimensions, or companion product stated in the application section.
Does the listing include unrelated installation parts?No. Only the exact component or kit identified in the included-items section is supplied.
Should existing components be inspected?Yes. Inspect the filter, couplers, clamps, sensor connection, bracket, and surrounding clearances at normal service intervals.
Is professional installation recommended?Professional installation is recommended whenever the work affects safety, pressurized fluid, suspension geometry, electrical wiring, or protective equipment setup.
What should be checked after installation?Verify secure mounting, correct routing or clearance, proper function, and every manufacturer-specified post-installation check before normal use.
Installation Instructions
- Confirm AWE Tuning 2660-15118, the application, and every listed restriction before installation.
- Allow the engine to cool, disconnect power where the current instructions require it, and protect the inlet from debris.
- Transfer only the factory sensor or fittings identified by AWE and install the support bracket in the documented mounting points.
- Assemble the carbon inlet, couplers, clamps, and filter without stressing the sensor wiring or nearby hoses.
- Check hood, brace, engine-movement, and wiring clearance before tightening every connection.
- Start the engine, inspect for air leaks or warning lights, and recheck the clamps after the first heat cycle.




