View vehicle applications
Fitment notes and restrictions
Description
Add firmer B6 damping while retaining the factory spring and ride height
Bilstein 19-313115 is a B6 Performance front spring-bearing strut for supported Volvo XC60 and XC90 models without electronic suspension. Its application-specific twin-tube gas-pressure valving is designed as a handling upgrade at factory ride height while reusing the original spring.
Key Features
- 19-313115 application-specific B6 Performance valving
- Front spring-bearing strut for factory ride height
- Twin-tube gas-pressure design
- Fixed spring seat for the OE factory spring
- Stem upper mount and base-cup lower mount
- Limited lifetime manufacturer warranty
Application Details and Restrictions
| Years | Make | Model | Verified Application and Notes |
|---|---|---|---|
| 2018-2022 | Volvo | XC60 | Front; without electronic or active suspension |
| 2017-2021 | Volvo | XC90 | Front; without electronic suspension; chassis/VIN 140101 or later |
| Excluded | Volvo | XC60 and XC90 | Vehicles equipped with electronic suspension or factory air ride |
Specifications
| Detail | Value |
|---|---|
| Manufacturer Part Number | 19-313115 |
| Series | B6 Performance |
| Position | Front axle |
| Design | Spring-bearing strut |
| Internal Design | Twin-tube gas pressure |
| Upper Mount | Stem |
| Lower Mount | Base cup |
| Extended Length | 527 mm |
| Compressed Length | 389 mm |
| Spring Seat | Fixed and included |
| Quantity | One strut |
| California Proposition 65 | Warning: Cancer and reproductive harm. See www.P65Warnings.ca.gov. |
What's Included
- One Bilstein 19-313115 front strut
- Spring-seat isolator and retaining ring shown in the exact-product gallery
- Factory spring and vehicle mounting bolts are not included
About Bilstein
Bilstein engineers OE-replacement and performance dampers with vehicle-specific valving. The B6 line is intended for drivers who want increased damping control at standard ride height without replacing the factory spring with a lowering spring.
Related Parts
- A matching second front strut for axle-balanced service
- Application-correct strut mount, dust boot, and bump stop inspected during installation
- Professional four-wheel alignment after replacement
FAQ
What is the 19-313115?It is one Bilstein B6 Performance front spring-bearing strut for the supported Volvo XC60 and XC90 applications.
Does it fit vehicles with electronic suspension?No. Exact-application sources specify vehicles without electronic or active suspension.
What is the XC90 chassis restriction?Supported XC90 applications require chassis or VIN sequence 140101 or later.
Is a factory spring reused?Yes. The B6 strut is designed to pair with the original factory spring at standard ride height.
Is this sold as a pair?No. The listing is for one front strut; inspect and service dampers in axle-balanced pairs where appropriate.
Is the spring seat included?Yes. The fixed spring seat is part of the strut assembly.
Is an alignment required?A professional alignment is recommended after front strut replacement and suspension fastener work.
What warranty applies?Bilstein lists a limited lifetime warranty for qualifying original purchasers, subject to current terms and correct installation.
Installation Instructions
- Confirm the package identifies 19-313115, the vehicle application, the absence of electronic suspension, and the XC90 chassis restriction where applicable.
- Have trained personnel inspect both front dampers, mounts, springs, bump stops, boots, and related suspension joints.
- Record ride height and alignment, then raise and support the vehicle at approved points.
- Remove the original front strut assembly using the current Volvo service procedure and a suitable spring compressor.
- Transfer only serviceable OE spring and related components in the correct order and orientation.
- Install the Bilstein strut with new application-required locking hardware where specified by Volvo.
- Torque all fasteners at the required suspension position using current Volvo values.
- Complete an alignment, verify sensor and hose routing, and road-test for noise, clearance, and controlled damping.




