BRExhaust 107-0123 front pipe inlet and flex-joint view
BRExhaust 107-0123 front pipe opposite-side view with hardware
BRExhaust 107-0123 front pipe profile view
BRExhaust 107-0123 complete front pipe kit with bolts and gaskets
Click to zoom in
View vehicle applications

Description

Replace the complete front pipe assembly without fabrication

BRExhaust 107-0123 is a direct-fit front pipe kit for the supported Acura MDX, Acura ZDX, and Honda Pilot applications. Its mandrel-bent stainless construction follows the original routing and combines two bolt-on inlets, one outlet, welded hanger, oxygen-sensor port, and exact installation hardware in one replacement assembly.

Key Features

  • 107-0123 exact direct-fit front pipe configuration
  • Mandrel-bent stainless-steel construction
  • Two 2-inch bolt-on inlets and one 2.25-inch bolt-on outlet
  • Integrated oxygen-sensor port and welded hanger
  • Application-specific hardware supports installation without fabrication
  • Leaves the original emissions equipment in place
  • Two-year unlimited-mileage construction warranty subject to current terms

Application Details and Restrictions

Years Make Model Verified Application and Notes
2007-2013 Acura MDX 3.7L V6
2010-2013 Acura ZDX 3.7L V6
2009-2015 Honda Pilot 3.5L V6

Specifications

Detail Value
Manufacturer Part Number 107-0123
Type Direct-fit front pipe kit
Material Stainless steel
Main Pipe Diameter 2.25 inches
Inlets Two; 2-inch inside diameter; bolt-on
Outlet One; 2.25-inch inside diameter; bolt-on
Bend Type Mandrel bent
Welded Hanger Yes
Oxygen Sensor Port Yes
Clamps Included No
OE Interchange 18210-STX-A02

What's Included

  • One BRExhaust 107-0123 direct-fit front pipe assembly
  • Nine nuts and nine bolts
  • Three ring gaskets
  • Installation instructions
  • Catalytic converters, mufflers, clamps, and unrelated vehicle hardware are not included

About BRExhaust

BRExhaust is MagnaFlow's replacement-exhaust line, focused on application-specific systems that restore factory-style fit, routing, sound control, and emissions-equipment placement with complete hardware kits where specified.

Related Parts

  • Application-correct catalytic converters and rear exhaust inspected before installation
  • Replacement rubber exhaust isolator if the original hanger is cracked or stretched
  • New oxygen sensor only when inspection or diagnosis shows replacement is required

FAQ

What is the 107-0123?

It is an application-specific BRExhaust direct-fit front pipe assembly for the listed Acura and Honda V6 applications.

Which vehicles fit?

The verified fitment covers 2007-2013 Acura MDX, 2010-2013 Acura ZDX, and 2009-2015 Honda Pilot with the engines shown in the table.

Is this a universal pipe?

No. The flange geometry, hanger, oxygen-sensor port, and routing are specific to the verified vehicle applications.

Are catalytic converters included?

No. This kit replaces the front pipe assembly and leaves the original emissions equipment in place.

Does installation require welding?

No. BRExhaust specifies a direct bolt-on installation for the supported applications.

Are clamps included?

No. The exact manufacturer specification lists no clamps for this flange-connected assembly.

What hardware is included?

The kit includes nine nuts, nine bolts, and three ring gaskets.

What warranty applies?

BRExhaust lists a two-year unlimited-mileage warranty, subject to its current terms and correct application and installation.

Installation Instructions

  1. Confirm the package identifies 107-0123 and the vehicle year, model, and engine match the fitment table.
  2. Allow the exhaust to cool, disconnect the battery as directed, and support the vehicle at approved lift points.
  3. Inspect the catalytic converters, rear exhaust connection, oxygen sensor, hanger, heat shields, and surrounding components before removal.
  4. Disconnect the oxygen sensor and remove only the original front pipe assembly and hardware being replaced.
  5. Position the supplied ring gaskets and install the replacement pipe loosely with the supplied bolts and nuts.
  6. Reconnect the hanger and oxygen sensor, then verify clearance around the body, drivetrain, suspension, wiring, and heat-sensitive parts.
  7. Tighten all flange hardware to the current BRExhaust and vehicle specifications.
  8. Start the engine, inspect every joint for leaks or contact, and recheck alignment and fastener torque after the first heat cycles.

BRExhaust Direct-Fit Front Pipe Kit for MDX, ZDX and Pilot

Magnaflow
MAG107-0123
888563178110
Exhaust Front Pipe Kit
53 Units In Stock
$ 279.17
$ 279.17

Military & First Responders

Military & First Responders

A program for military members and first responders, with dedicated verification and support for your next build.

Learn More & Apply

Your cart

×