DV8 Motorcraft (Ford) Parking Sensor Bezels (Set of 4)

Clean, Factory-Style Parking Sensor Bezels That Integrate Flush with Your Ford's Bumper

The DV8 MCFSNSR-01 is a set of four replacement parking sensor bezels designed to provide a clean, factory-integrated appearance for aftermarket parking sensors installed on Ford trucks and SUVs. Cut-in aftermarket sensors often lack a finished mounting bezel, leaving exposed sensor holes that look unfinished. The DVEMCFSNSR-01 fills that gap with a precision-fit black ABS bezel sized for standard 1.1-inch sensor cutouts, delivering a polished, intentional look that blends with the factory bumper texture.

Key Features

• Set of 4 bezels designed to finish standard 1.1-inch aftermarket parking sensor installations
• Black ABS construction matches factory bumper material and texture
• Snap-fit or adhesive-compatible mounting for secure panel integration
• Clean, flush fit eliminates the unfinished look of bare aftermarket sensor holes
• Compatible with most round parking sensors with a 1.1-inch mounting hole requirement
• Low-profile design does not protrude beyond the bumper surface
• Suitable for use on DV8 Offroad aftermarket bumpers as well as factory Ford bumpers with sensor cutouts

Specifications

What's Included

• 4x DV8 MCFSNSR-01 Parking Sensor Bezels (Black ABS)

About DV8 Offroad

DV8 Offroad designs and manufactures bumpers, rock sliders, roof racks, and accessory components for trucks and SUVs. Their product line focuses on bolt-on compatibility with factory mounting points and clean integration with OEM body lines. Accessories like the MCFSNSR-01 bezels are engineered to complement DV8 bumper systems while remaining compatible with standard aftermarket sensor hardware.

Frequently Asked Questions

The MCFSNSR-01 bezels are designed for standard round parking sensors with a 1.1-inch mounting hole diameter. Confirm your sensor's outer diameter before ordering, as parking sensors are available in multiple sizes and not all sensors will seat correctly in a 1.1-inch bezel.

Yes. The DVEMCFSNSR-01 bezels are sized to the standard 1.1-inch parking sensor cutout used by many aftermarket sensor brands. As long as your sensor fits a 1.1-inch hole, the bezels should provide a compatible mount and finished appearance.

The bezels are designed with Ford trucks and SUVs as the primary application, particularly for use with DV8 aftermarket bumpers. However, since they are sized to a standard 1.1-inch sensor cutout, they can be used on any bumper that accepts sensors of that dimension, regardless of vehicle make.

The bezels are designed for snap-fit or adhesive-compatible installation into the sensor cutout hole. Installation method may vary based on bumper material and sensor housing design. Confirm the mounting method is appropriate for your specific bumper before installation.

No special tools are typically required. The bezels snap or press into the sensor cutout and can usually be installed by hand. A trim removal tool may be helpful if working in tight bumper locations or when removing existing bezels.

Properly installed bezels that sit flush with the bumper surface should not interfere with sensor operation. Ensure the bezel does not protrude in front of the sensor face or obstruct the sensor's detection cone when fitting.

The DVEMCFSNSR-01 bezels are ABS plastic, which accepts automotive-grade adhesion promoter and paint. For painted finishes, lightly scuff the bezel surface, apply adhesion promoter, and use a flexible bumper paint rated for ABS substrates.

Yes. The bezels are compatible with any bumper that accepts a 1.1-inch sensor cutout. They are not exclusive to DV8 bumpers and can be used on any steel or ABS aftermarket bumper with correctly sized sensor holes.

Installation Instructions

1. Confirm the sensor holes in your bumper are cut to the correct 1.1-inch diameter before installing the bezels.
2. Clean the area around each sensor hole to remove dirt, grease, or debris that could prevent a flush fit.
3. Insert each DV8 MCFSNSR-01 bezel into the sensor hole from the front of the bumper, aligning the bezel tabs or retaining features with the hole edge.
4. Press the bezel firmly until it seats flush and snaps into position, or apply a compatible adhesive to the back flange if your bumper material requires it.
5. Insert the parking sensor into the bezel from the front, pressing until the sensor is fully seated in the housing.
6. Connect the sensor wiring harness and confirm sensor operation with a test cycle before final assembly.