Edelbrock Ford 289 and 302 E-Series head bolts with step washers
Click to zoom in
View vehicle applications

Description

Secure supported Ford 289/302 aluminum heads with application-specific chromoly hardware

Edelbrock 85522 is an E-Series cylinder-head fastener set for 1963-1996 Ford 289 and 302 small-block engines with standard 7/16-inch head-bolt bosses and the listed Edelbrock aluminum cylinder heads. The kit uses heat-treated chromoly bolts, rolled threads, small hex heads, step washers, and a sealed black-oxide finish.

Key Features

  • Designed for Ford 289 and 302 small-block engines with 7/16-inch head-bolt bosses
  • Supports the exact Edelbrock aluminum cylinder-head part numbers listed below
  • Chromoly construction with 190,000 PSI yield tensile strength
  • Threads are rolled after heat treatment for improved form and strength
  • Small hex heads provide socket clearance in tight installations
  • Black-oxide finish with sealer and stamped Edelbrock E logo
  • Step washers adapt the 7/16-inch bolts to 1/2-inch holes in supported aluminum heads

Application details and restrictions

Years / Scope Make Model / Component Requirement
1963-1996 engine family Ford 289 / 302 small-block V8 Standard 7/16-inch head-bolt bosses and a supported Edelbrock aluminum cylinder head

Edelbrock lists cylinder heads 60217, 60219, 60225, 60229, 60249, 60255, 60259, 60319, 60329, 60349, 60359, 60367, 60369, 60379, 60389, 60399, 602479, and 602579. Ford 289/302 applications require head-bolt bushings 9680 where specified by Edelbrock. Boss 302 clone engines require Edelbrock bushings with integral washers 9680 in place of the supplied washers. Vehicle year and model alone do not establish compatibility.

Specifications

Detail Value
Manufacturer Part Number 85522
Engine Family Ford 289 / 302 small-block V8
Thread Diameter 7/16 inch
Thread 7/16-14 coarse
Bolt Lengths Ten 2.50-inch bolts and ten 4.00-inch bolts
Washers Twenty step washers, 1/2-inch ID x 7/8-inch OD x 0.120-inch thick
Material Chromoly
Yield Tensile Strength 190,000 PSI
Finish Black oxide with sealer
Warranty 12 months
California Proposition 65 Warning for chromium exposure applies

What's Included

  • Ten 7/16-14 x 2.50-inch E-Series head bolts
  • Ten 7/16-14 x 4.00-inch E-Series head bolts
  • Twenty 1/2-inch ID x 7/8-inch OD x 0.120-inch step washers
  • Edelbrock head-bolt installation instructions
  • Edelbrock 9680 head-bolt bushings are required where specified and are not included

About Edelbrock

Edelbrock engineers cylinder heads and installation hardware as matched engine systems. This E-Series kit is built around the thread size, head-bolt-hole diameter, torque procedure, and supported Ford small-block cylinder-head combinations listed by Edelbrock.

Related Parts

  • No related store product is linked because supporting components must be verified for the exact vehicle, engine, transmission, and current Edelbrock configuration.

FAQ

What is the 85522?

It is cylinder head bolt kit for the exact application and restrictions shown above.

Which engines are supported?

Edelbrock specifies Ford 289 and 302 small-block V8 engines with standard 7/16-inch head-bolt bosses.

Are these bolts for every Ford small-block?

No. The kit is not the 1/2-inch 351W fastener set and requires the supported block and cylinder-head combination.

Which cylinder heads are supported?

Use only the Edelbrock aluminum cylinder-head part numbers listed in the application section and confirm the current cylinder-head instructions.

Are head-bolt bushings included?

No. Edelbrock 9680 bushings are required where specified and must be obtained separately.

What torque does Edelbrock specify?

Edelbrock specifies 65 to 70 lb-ft for 7/16-inch bolts, applied in four steps and in the factory tightening sequence.

Should the bolts be lubricated?

Yes. Edelbrock instructs installers to apply oil or suitable thread lubricant to the threads and beneath bolt heads and washers.

Is a re-torque required?

Edelbrock recommends re-torquing after initial startup and a two-to-three-hour cool-down.

Installation Instructions

  1. Confirm the engine is a Ford 289 or 302 small-block with 7/16-inch head-bolt bosses and that the exact Edelbrock cylinder-head number is listed for this kit.
  2. Read the current Edelbrock cylinder-head and bolt-kit instructions, clean and inspect the block threads, and obtain Edelbrock 9680 bushings when the application requires them.
  3. Install the supported cylinder heads and supplied step washers in the locations shown by Edelbrock; Boss 302 clone engines use 9680 integral-washer bushings instead of the supplied washers.
  4. Apply oil or suitable thread lubricant to every bolt thread and beneath each bolt head and washer as directed by Edelbrock.
  5. Follow the factory tightening sequence and bring the 7/16-inch bolts to 65 to 70 lb-ft in four steps: 30, 40, 50, then 65 to 70 lb-ft.
  6. Complete the remaining cylinder-head installation according to Edelbrock and Ford service procedures, checking that every washer seats flat and no bolt bottoms in its hole.
  7. After initial startup, allow the engine to cool for two to three hours and re-torque the fasteners as recommended by Edelbrock.

Edelbrock E-Series Head Bolt Kit for Ford 289/302 Engines

Edelbrock
EDE85522
085347855223
Head Stud & Bolt Kits
54 Units In Stock
$ 77.95
$ 77.95

Military & First Responders

Military & First Responders

A program for military members and first responders, with dedicated verification and support for your next build.

Learn More & Apply

Your cart

×