-19%
Sold out
Click to zoom in
The Koni 8745.1419R is a Special Active front right shock absorber built specifically for the 2019 and newer Toyota RAV4 XA50 platform, covering all available engine configurations. Using Koni's latest generation of patented Frequency Selective Damping (FSD) technology, the 8745.1419R automatically adapts its damping rate to road conditions in real time, delivering sharper handling and improved road holding without sacrificing ride comfort. This is a direct 1:1 bolt-in replacement for the factory strut insert, requiring no modifications to the existing suspension geometry. The 8745.1419R is the front right unit and must be installed with the front left shock 8745.1419L for a matched pair.
Why the Koni 8745.1419R Outperforms Stock
Factory shock absorbers on the Toyota RAV4 XA50 are calibrated for a broad average of drivers and road conditions. The result is a compromise that allows body roll, vague steering feedback, and gradual fade under load. The 8745.1419R uses Koni's Frequency Selective Damping technology to separate high-frequency inputs (rough pavement, small bumps) from low-frequency inputs (cornering, braking, acceleration loads). High-frequency inputs pass through with minimal resistance for a supple, comfortable ride. Low-frequency inputs are damped firmly, reducing body roll and keeping the tire planted for precise steering response.
The twin-tube gas pressure design maintains consistent oil temperature and aeration control, preventing shock fade during extended driving or spirited back-road use. Technology proven on over 10 million factory-equipped vehicles worldwide backs every Koni Special Active unit.
Koni Special Active FSD Technology
The Frequency Selective Damping system at the core of the 8745.1419R operates without driver input or electronic sensors. A passive internal valve responds to the frequency and velocity of suspension inputs, automatically stiffening for slow, large body movements while softening for fast, small road-surface inputs. The result is a shock absorber that genuinely does two jobs at once: performance handling and daily-driver comfort. No adjustments, no switches, no modes to manage.
Fitment: 2019+ Toyota RAV4 XA50
The 8745.1419R fits the Toyota RAV4 XA50 (fifth generation) built from the 2019 model year forward, spanning all available drivetrain and engine configurations including FWD, AWD, hybrid, and plug-in hybrid variants. Also fits the Suzuki Across (2020+), which shares the XA50 platform. Confirm your model year and platform code before ordering. This is a single right-side unit.
| Year | Make | Model | Trim / Engine | Position |
|---|---|---|---|---|
| 2019 | Toyota | RAV4 (XA50) | All Trims / All Engines | Front Right |
| 2020 | Toyota | RAV4 (XA50) | All Trims / All Engines | Front Right |
| 2021 | Toyota | RAV4 (XA50) | All Trims / All Engines | Front Right |
| 2022 | Toyota | RAV4 (XA50) | All Trims / All Engines | Front Right |
| 2023 | Toyota | RAV4 (XA50) | All Trims / All Engines | Front Right |
| 2024 | Toyota | RAV4 (XA50) | All Trims / All Engines | Front Right |
| 2025 | Toyota | RAV4 (XA50) | All Trims / All Engines | Front Right |
| 2020 | Suzuki | Across | 2.5 Hybrid AWD | Front Right |
| 2021 | Suzuki | Across | 2.5 Hybrid AWD | Front Right |
| 2022 | Suzuki | Across | 2.5 Hybrid AWD | Front Right |
| 2023 | Suzuki | Across | 2.5 Hybrid AWD | Front Right |
| 2024 | Suzuki | Across | 2.5 Hybrid AWD | Front Right |
Full Specifications
| Specification | Detail |
|---|---|
| Part Number | 8745.1419R |
| UPC / EAN | 8712167186900 |
| Series | KONI Special Active |
| Position | Front Right |
| Shock Type | Gas Pressure, Twin-Tube |
| Design | Suspension Strut (MacPherson) |
| Technology | Frequency Selective Damping (FSD), Built-in Adjustable |
| Mounting Type | Clamp Below, Top Pin |
| Max Extended Length | 604 mm |
| Color | Red |
| Quantity | 1 (Single Unit) |
| Box Dimensions | 570 mm L x 190 mm W x 190 mm H |
| Fits | 2019+ Toyota RAV4 XA50, 2020+ Suzuki Across |
| Warranty | Koni Limited Warranty (see koni-na.com for current terms) |
What Is Included
- 1x Koni 8745.1419R Special Active front right shock absorber
- Mounting hardware as specified by Koni for this application
Installation Overview
The 8745.1419R is a direct-fit strut replacement designed for technicians familiar with MacPherson strut service. A spring compressor is required to safely transfer the OEM coil spring to the new shock body. Professional installation is strongly recommended. Standard front strut service on the RAV4 XA50 typically requires 1.5 to 2.5 hours per side at a shop.
- Tools required: spring compressor, torque wrench, socket set, strut nut socket
- Compress and transfer factory coil spring to the new Koni strut body
- Torque all fasteners to Toyota factory specification
- A four-wheel alignment is strongly recommended after strut replacement
- Install the matching 8745.1419L on the left side for balanced handling
About Koni
Koni has been engineering precision shock absorbers since 1857, building a legacy on motorsport success and OEM supply contracts with major automakers worldwide. The Koni Special Active series brings the brand's Frequency Selective Damping technology from the racetrack to daily-driven vehicles. Technology proven on over 10 million factory-equipped vehicles is the backbone of every Special Active unit Koni produces.
Frequently Asked Questions
What does the Koni 8745.1419R fit?
The 8745.1419R fits the Toyota RAV4 XA50 fifth-generation platform from the 2019 model year onward, covering all engine variants including 2.0L, 2.5L, hybrid, and plug-in hybrid. It also fits the Suzuki Across (2020+), which shares the same XA50 chassis architecture.
Do I need to buy two units for a full front replacement?
Yes. The 8745.1419R covers the front right position only. For a complete front axle upgrade, you also need the Koni 8745.1419L for the front left. Installing matched shocks on both sides is required for balanced handling.
What is Koni Frequency Selective Damping?
FSD is Koni's patented passive adaptive damping system. An internal valve reads suspension input frequency and automatically adjusts damping: soft for high-frequency road surface inputs for ride comfort, firm for low-frequency body motion inputs for handling control. No electronics or driver adjustment required.
Is a spring compressor required to install the 8745.1419R?
Yes. The 8745.1419R replaces the strut cartridge in a MacPherson-style front suspension. The factory coil spring must be safely compressed and transferred to the new unit. This job requires proper spring compressor equipment. Professional installation is recommended.
Does the 8745.1419R require a wheel alignment after installation?
Yes. Any front strut replacement on the Toyota RAV4 XA50 should be followed by a professional four-wheel alignment. Strut removal and reinstallation affects front camber and toe settings, which will alter tire wear and handling if not corrected.
Will the Koni 8745.1419R void my Toyota RAV4 factory warranty?
No. Under the federal Magnuson-Moss Warranty Act, a manufacturer cannot void your factory warranty simply because you installed an aftermarket part. The dealer or manufacturer must prove that the aftermarket part directly caused the specific failure being claimed before warranty coverage can be denied on any related component.
Is the Koni 8745.1419R compatible with RAV4 hybrid and plug-in hybrid models?
Yes. The 8745.1419R fits all powertrain variants of the Toyota RAV4 XA50, including the standard 2.5L four-cylinder, 2.5L hybrid (AXAH52/AXAH54), and 2.5L plug-in hybrid. Confirm your specific chassis code if you have any questions about your trim.
Does this product carry a Prop 65 warning?
Yes. California residents: This product contains chemicals known to the State of California to cause cancer and reproductive harm. See www.p65warnings.ca.gov.
How does the Koni Special Active compare to the factory RAV4 shocks?
The factory RAV4 XA50 shocks use a fixed-rate damping tune. The 8745.1419R uses FSD technology that automatically adjusts to real-time driving conditions, providing better body control in corners and under braking while maintaining or improving ride quality on rough surfaces.
What is the extended length of the 8745.1419R?
The Koni 8745.1419R has a maximum extended length of 604 mm, consistent with the OEM strut dimensions on the Toyota RAV4 XA50 front suspension.
California residents: Prop 65 Notice
This product contains chemicals known to the State of California to cause cancer and reproductive harm. See www.p65warnings.ca.gov.
KONI
KONI shocks and suspension for cars, trucks, and SUVs are stocked at Black Ops Auto Works. Shop KONI STR.T adjustable shocks, Special Active shocks, Sport shocks, FSD (Frequency Selective Damping) shocks, and complete KONI coilover kits for Mustang, Camaro, Miata, Jeep Grand Cherokee, Toyota RAV4, and a wide range of domestic, European, and import platforms. Every KONI shock is filterable by year, make, model, trim, and drivetrain so the correct valving, length, and mounting style ships the first time. Black Ops Auto Works carries 590 KONI SKUs across STR.T, Special Active, Sport, and FSD categories. What This Collection Covers KONI has built shock absorbers for street, track, and off road use since 1945, with a damper lineup that spans mild daily driver upgrades to fully adjustable track focused shocks. This collection covers KONI shocks and struts across the brand's core product lines, each tuned for a different balance of comfort, handling, and adjustability. STR.T Adjustable...
View KONI Products
Shocks and Struts
Shocks and struts for cars, trucks, SUVs, and Jeeps are stocked at Black Ops Auto Works. Shop front and rear shocks, loaded strut assemblies, monotube shocks, twin-tube shocks, reservoir shocks, and steering dampers for daily drivers, lifted trucks, tow rigs, off-road builds, and muscle cars on Hellcat, Trackhawk, TRX, HEMI, LS, LT, Coyote, and EcoBoost platforms. Every shock and strut is filterable by year, make, model, trim, drivetrain, front or rear position, and ride height so the correct part ships the first time. Black Ops Auto Works carries 5,188 shock and strut SKUs across construction type, application, and vehicle use. What This Category Covers Shocks and struts damp spring oscillation so the tire stays planted on the road and are the most common suspension replacement job on any vehicle. A shock absorber is a standalone damping unit that bolts between the chassis and axle or lower control arm. A strut is a structural suspension member that combines damping with the sp...
View Shocks and Struts Products
Suspension
Suspension parts and complete kits for cars, trucks, SUVs, Jeeps, and off-road builds are stocked at Black Ops Auto Works. Shop coilovers, lowering springs, lift kits, leveling kits, shocks and struts, sway bars, control arms, tie rods, ball joints, bushings, chassis bracing, alignment hardware, air suspension, and complete stage kits from Bilstein, KW, Ohlins, Fox, KING, ICON, BC Racing, Silvers, Eibach, H&R, Swift Springs, Whiteline, Energy Suspension, Moog, SPC Performance, Rough Country, ReadyLIFT, BDS, Skyjacker, Air Lift, Firestone, and Black Ops Auto Works. Start with a matched shock and spring package or a full coilover kit, then layer in sway bars, chassis bracing, and camber adjustment hardware. Every part is filterable by year, make, model, trim, and drivetrain to confirm fitment before ordering. What This Category Covers Suspension is the highest-leverage handling upgrade on any vehicle. A properly matched shock, spring, and sway bar package produces measurable i...
View Suspension Products