View vehicle applications
Fitment notes and restrictions
Description
Keep charge temperatures under control when the EcoBoost stays under load
Mishimoto MMINT-MUS4-24BK replaces the compact factory charge-air cooler with a larger black bar-and-plate intercooler engineered for the S650 Mustang EcoBoost. Mishimoto testing documented lower outlet temperatures and improved power on a stock tune while retaining the factory mounting area and compatible charge piping.
Key Features
- MMINT-MUS4-24BK exact black intercooler configuration
- Bar-and-plate core with cast aluminum end tanks
- Up to 60 degrees F lower charged-air outlet temperature in Mishimoto testing
- Published support for up to 526 horsepower and 50 psi
- Core volume increased by 60 percent over the factory intercooler
- 2.44-inch inlet and outlet ports
- Pre-drilled and tapped NPT sensor port
- No cutting required for the documented direct-fit installation
Fitment
| Years | Make | Model | Verified Application and Notes |
|---|---|---|---|
| 2024-2026 | Ford | Mustang EcoBoost | 2.3L EcoBoost I4; S650 chassis |
| 2024-2026 | Ford | Mustang EcoBoost Premium | 2.3L EcoBoost I4; S650 chassis |
| Requirement | Charge piping | Factory or compatible Mishimoto piping | Intercooler-only listing; charge pipes are not included |
Specifications
| Detail | Value |
|---|---|
| Manufacturer Part Number | MMINT-MUS4-24BK |
| Core Type | Bar and plate |
| End Tanks | Cast aluminum |
| Finish | Black |
| Overall Size | 35.7 x 6.5 x 5.3 inches |
| Core Size | 22.83 x 6.08 x 3.54 inches |
| Inlet | 2.44 inches |
| Outlet | 2.44 inches |
| Maximum Recommended Boost | 50 psi |
| Maximum Recommended Horsepower | 526 hp |
| Engine | 2.3L EcoBoost I4 |
| Chassis | S650 |
| UPC | 840197725566 |
What's Included
- One Mishimoto MMINT-MUS4-24BK black performance intercooler
- One deflector panel kit
- One bracket kit with application-specific mounting hardware and rubber isolators
- Charge pipes, tools, and unrelated vehicle parts are not included
About Mishimoto
Mishimoto develops vehicle-specific cooling products through dimensional design, instrumented testing, and installation validation. Its lifetime warranty applies under the manufacturer's current terms and exclusions.
Related Parts
- Mishimoto charge-pipe kit verified for the same 2024+ Mustang EcoBoost platform
- Replacement clamps and seals specified by the current installation guide
- Data-logging sensor compatible with the provided NPT port
FAQ
What is the MMINT-MUS4-24BK?It is the black Mishimoto performance intercooler for the supported S650 Mustang EcoBoost application.
Which Mustang engine is supported?Mishimoto specifies the 2.3-liter EcoBoost I4 in the 2024+ S650 Mustang.
Does this listing include charge pipes?No. This is the intercooler, deflector panel, bracket kit, and installation hardware; charge pipes are separate.
Is a tune required?Mishimoto reports its published test gains on a stock tune and does not require a tune for the intercooler alone.
How much power can the intercooler support?Mishimoto lists a maximum recommended rating of 526 horsepower and 50 psi.
Will it work with the factory charge piping?Yes. Mishimoto designed the intercooler to work with factory piping and its compatible charge-pipe kit.
Is cutting required?No cutting is identified in the current direct-fit installation procedure, but the bumper and related front-end components must be removed for access.
What warranty applies?Mishimoto lists its lifetime warranty, subject to the current manufacturer terms, proof-of-purchase requirements, and exclusions.
Installation Instructions
- Confirm the carton identifies MMINT-MUS4-24BK and inspect the intercooler, deflector panel, brackets, isolators, and hardware before disassembly.
- Allow the vehicle to cool, disconnect the battery, and review the current Mishimoto installation guide in full.
- Raise and support the Mustang at approved lift points, then remove the undertray, front bumper, ducting, and factory intercooler as documented.
- Transfer only the documented factory components and install the supplied brackets and rubber isolators in their specified positions.
- Mount the intercooler and deflector panel without forcing the end tanks, ports, ducting, or surrounding cooling components.
- Reconnect the factory or compatible Mishimoto charge piping and secure every clamp and sensor-port plug or fitting.
- Reinstall the bumper, ducting, and underbody panels after confirming clearance and unobstructed airflow.
- Start the engine, inspect for boost leaks or contact, and recheck every connection after the first heat cycles.
California Proposition 65 Warning: Cancer and reproductive harm. See www.P65Warnings.ca.gov.




