SPC 67817 Toyota Highlander adjustable rear camber arm
SPC 67817 installed rear camber arm location illustration
Click to zoom in
View vehicle applications

Description

Restore rear alignment range while retaining OE-like bushing compliance

SPC Performance 67817 adds rear camber adjustment to the Toyota Highlander so an alignment technician can return the suspension toward factory specification after ride-height or geometry changes. The non-handed upper arm combines a bonded-rubber inner bushing with an xAxis sealed flex-joint outer connection.

Key Features

  • 67817 provides plus or minus 3 degrees of rear camber adjustment
  • Stamped, non-handed rear upper control-arm construction
  • Bonded-rubber inner bushing supports OE-like ride quality
  • xAxis sealed flex-joint outer connection
  • Grease fitting is included for the outer joint
  • Limited lifetime manufacturer warranty

Application Details and Restrictions

Years Make Model Verified Application and Notes
2020-2025 Toyota Highlander Rear upper camber arm; all manufacturer-listed Highlander configurations
Excluded Toyota Highlander 2026 Not listed on the current manufacturer product page

Specifications

Detail Value
Manufacturer Part Number 67817
Position Rear upper
Adjustment Range Camber plus or minus 3 degrees
Minimum Length 280 mm
Maximum Length 305 mm
Inner Bushing Bonded rubber
Outer Joint xAxis sealed flex joint
Quantity One arm
Warranty Limited lifetime
California Proposition 65 Warning: Cancer and reproductive harm. See www.P65Warnings.ca.gov.

What's Included

  • One 67817 adjustable rear camber arm
  • One lower brake-line bracket
  • One M6 bracket bolt
  • Factory control-arm mounting hardware is reused as directed

About SPC Performance

SPC Performance develops alignment correction parts and service tools for street, performance, and professional alignment applications. Its Highlander arm is designed to add measurable rear camber range while maintaining compliant bushing behavior.

Related Parts

  • SPC 81139 magnetic camber gauge for alignment measurement
  • Vehicle-specific alignment service after installation

FAQ

What is the 67817?

It is a single adjustable rear upper camber arm for the manufacturer-listed Toyota Highlander application.

How much camber adjustment is available?

SPC specifies plus or minus 3 degrees of rear camber adjustment.

Is this sold as a pair?

No. The manufacturer identifies the product as one non-handed arm.

Does it fit a 2026 Highlander?

No 2026 application appears on the current SPC product page, so this listing stops at 2025.

Are bushings included?

Yes. The arm has a bonded-rubber inner bushing and an xAxis sealed flex-joint outer connection.

Is mounting hardware included?

The supplied brake-line bracket and M6 bolt are included; the current instructions direct the installer to retain factory arm hardware.

Is an alignment required?

Yes. Measure alignment before removal and complete a professional four-wheel alignment after installation.

What warranty applies?

SPC lists a limited lifetime warranty, subject to its current warranty terms and installation requirements.

Installation Instructions

  1. Confirm the package identifies 67817 and the vehicle is a manufacturer-listed 2020-2025 Toyota Highlander.
  2. Have trained personnel inspect the suspension, tire condition, and existing alignment before disassembly.
  3. Raise and support the rear suspension at approved points, then remove the wheel.
  4. Disconnect the brake-line bracket and remove the original upper control arm using the vehicle service procedure.
  5. Install the supplied lower brake-line bracket on the SPC arm with the supplied M6 bolt.
  6. Install the arm with retained factory mounting hardware and orient the adjustment assembly as shown in the current SPC instructions.
  7. Torque all fasteners to the current vehicle and SPC specifications at the required suspension position.
  8. Complete a professional alignment, verify clearance, and recheck fasteners after the prescribed inspection interval.

SPC Performance Rear Camber Arm for 2020-2025 Toyota Highlander

SPC67817
082642678175
Rear Camber Arm
75 Units In Stock
$ 210.62
$ 210.62

Military & First Responders

Military & First Responders

A program for military members and first responders, with dedicated verification and support for your next build.

Learn More & Apply

Your cart

×