exhaust hardware banner 1942x809.webp

Explore Exhaust Hardware at Black Ops Auto Works. Match engine, body configuration, factory exhaust equipment and connection dimensions. Check the exact component layout, included hardware and product-specific application notes.

  • Engine and exhaust-layout matching
  • Connection and clearance checks
  • Material and package contents

Questions about Exhaust Hardware? Ask our team before ordering or call (855) 221-9728.

Exhaust Hardware aftermarket parts and performance accessories

Shop exhaust clamps, fasteners, sensor-installation parts, silencers and fitting hardware at Black Ops Auto Works. Compare actual connection and service requirements across Kooks, Ticon, Innovate, QTP, Akrapovic and other listed references. Choose the component needed for the exhaust already fitted or the fabrication job being planned.

Clamp Profiles and Fasteners

Kooks ball/socket swivel-seal and slip-joint band clamps serve different interfaces. APR’s slip clamp, ISR’s specified turbine-discharge V-band clamp and Ticon/Mikalor clamp ranges also require their own mating dimensions. Nominal tube diameter alone does not establish the right clamp profile.

Mishimoto manifold studs, BBK header bolts and the BLOX fastener pack supply different hardware. Match thread, length, flange thickness and actual kit contents, then use the specified lubricant and tightening procedure.

Sensor Bungs, Extensions and Temporary Mounts

Innovate references distinguish temporary sensor-installation clamps, extended bungs, bung/plug kits and a heat-sink extender. Match the sensor, installation purpose, thread, placement and supported exhaust material. A temporary clamp is not the same as a permanent welded sensor location.

Kooks and Hellcat oxygen-sensor extension references have specific connector and routing requirements. An electrical extension and a threaded bung serve different functions; neither converts an incompatible sensor to the correct ECU/controller type.

Valve Service and Vehicle-Specific Fitting Kits

QTP’s replacement motor and intermediate wire service compatible QTEC components. They do not supply a complete cutout assembly or a new exhaust system. Identify the existing unit before selecting service hardware.

Akrapovic fitting references distinguish Panamera engine variants and a BMW OPF/GPF application. The separately listed G87 rear-wing fitting kit belongs to its named body component. Review the exact package rather than assuming every fitting kit is universal exhaust hardware.

Silencers, Hangers and Fabrication Pieces

ISR universal silencers and the R1-specific silencer need their stated exhaust/outlet dimensions and retention method. Remark exhaust finishers are separate appearance components, while PERRIN standard/long Forester hanger kits change support position.

Vibrant pie cuts, Ticon tube stock and Jeep exhaust-extension references provide different routing scopes. Plan the complete joint, material and clearance requirements with the fabricator. Check the components supplied and inspect the assembled system for leaks, contact and correct operation.

Choose Your Part

  • Identify clamp, fastener, sensor-installation, valve-service or routing scope.
  • Match exact joint profile, threads, connector or retained assembly.
  • Review package contents, dimensions and material/installation requirements.
  • Plan support, sensor placement, heat clearance and final checks.

Frequently Asked Questions

Are ball/socket and slip-joint clamps the same?

No. They secure different mating interfaces. Match the actual joint and clamp profile.

Does an oxygen-sensor extension include a sensor?

It supplies its stated extension hardware. Match the connector, routing and supported sensor/controller separately.

Is a QTEC replacement motor a complete cutout?

No. It is service hardware for the supported unit. Identify the existing cutout and exact required part.

Does every fitting kit in this category install an exhaust?

No. An Akrapovic rear-wing fitting reference is also listed. Choose by the actual product function and part number.

How should I choose a silencer?

Match the exhaust/outlet dimensions, retention system and explicit application. An R1-specific reference is separate from a dimensional universal item.

What should be checked after hardware service?

Follow the exact fastening procedure and inspect joint sealing, clearances, support and any affected sensor or valve operation.

Related Collections

Exhaust Components · Exhaust Adapters · Exhaust Hangers · Bungs

Military & First Responders

Military & First Responders

A program for military members and first responders, with dedicated verification and support for your next build.

Learn More & Apply

Your cart

×