-9%
Click to zoom in
3 Inch Stainless Band Clamp That Secures Slip Joint Exhaust Connections Without Leaking
The JI-TAS300 is a 3 inch stainless steel band clamp for slip joint exhaust connections, providing a clean, secure, and leak resistant method of joining two 3 inch exhaust pipe slip joints without welding. Slip joints are a common feature in performance exhaust systems because they allow sections of the exhaust to be assembled, adjusted, and disassembled during installation or maintenance. A quality band clamp at each slip joint is what determines whether that joint stays sealed and tight in service or develops leaks and noise over time. This band clamp uses T304 stainless steel to provide the corrosion resistance and clamping strength that a permanent exhaust joint demands.
For builders using Kooks modular exhaust components, race car builders, or anyone assembling a 3 inch performance exhaust system with slip joint connections, the JI-TAS300 is the hardware item that closes out each joint properly. It fits cleanly over standard 3 inch slip joint overlaps and tightens to draw the pipes together into a sealed connection. The stainless construction means it will not rust or deteriorate in the exposed undercarriage environment, and the band clamp design allows the joint to be opened again for maintenance without destroying the hardware.
Key Features
- Designed for 3 inch slip joint exhaust connections
- T304 stainless steel construction for corrosion resistance and long service life
- Band clamp design provides even clamping force around the full pipe circumference
- Allows slip joints to be opened and reseated for maintenance without replacing hardware
- Seals the slip joint against exhaust gas leaks
- Compatible with Kooks 3 inch exhaust system components
What's Included
- 1 x this band clamp 3 inch stainless steel band clamp for slip joint connections
Specifications
| Specification | Detail |
|---|---|
| Part Number (MPN) | JI-TAS300 |
| UPC | Contact us for UPC |
| Pipe Diameter | 3 inch |
| Clamp Type | Band Clamp |
| Connection Type | Slip Joint |
| Material | T304 Stainless Steel |
| Fitment | Universal (3 Inch Slip Joint Applications) |
Frequently Asked Questions
What is this band clamp used for?
This band clamp is a band clamp used to secure 3 inch slip joint exhaust connections. It clamps over the overlapping pipe ends at a slip joint to hold the connection together and seal it against exhaust gas leaks.
What is a slip joint in an exhaust system?
A slip joint is where one pipe section slides over or into another, with overlap that allows the joint to be assembled without welding. A band clamp draws the outer pipe against the inner to seal the connection. Slip joints are commonly used in modular exhaust systems for easier installation and maintenance access.
What pipe diameter does this band clamp fit?
This band clamp is sized for 3 inch exhaust pipe slip joints. Both the inner and outer pipe at the joint should be 3 inch nominal diameter.
Can this band clamp be reused after removing the exhaust?
Yes. This band clamp band clamp can typically be reused as long as the band and hardware are not damaged during removal. Inspect the clamp for cracks, distortion, or stripped threads before reusing.
Is this band clamp better than a U bolt clamp?
Band clamps provide more even clamping force around the full pipe circumference than U bolt clamps, which concentrate clamping force at two points. This makes band clamps more effective at sealing slip joints against exhaust gas leaks.
Will this band clamp hold a slip joint permanently without welding?
This band clamp provides a reliable seal and connection when properly torqued. It is a serviceable connection that can be loosened for disassembly. If a permanent non serviceable connection is required, welding is the alternative.
Is this band clamp compatible with non Kooks exhaust components?
Yes. Any 3 inch slip joint exhaust connection can use this band clamp, regardless of the component brand.
How tight should I torque this band clamp?
Tighten to the point where the slip joint is fully drawn together and the clamp is firm without distorting the pipe. Refer to any torque specification provided with Kooks exhaust components for guidance.
Is this band clamp sold individually?
Yes. Order as many as you have slip joint connections in your exhaust system.
What is the difference between this band clamp and JI-TAS250?
This band clamp is for 3 inch slip joints and the JI-TAS250 is for 2.5 inch slip joints. Both are T304 stainless band clamps for the same type of connection.
Installation Instructions
- Slide one pipe end into the other to form the slip joint, ensuring adequate overlap for a sealed connection.
- Slide this band clamp band clamp over the outer pipe so it sits centered over the overlapping section.
- Draw the clamp snug by hand, then use the appropriate wrench to tighten the clamp hardware.
- Tighten until the slip joint is fully drawn together and the clamp cannot be rotated on the pipe.
- Avoid over tightening, which can distort the pipe or strip the clamp threads.
- Start the engine and check for exhaust leaks at the slip joint after the first heat cycle.
- Re inspect and tighten if needed after the initial heat cycle.
Prop 65 Warning
WARNING: This product can expose you to chemicals including Chromium and Nickel, which are known to the State of California to cause cancer, birth defects or reproductive harm. For more information go to www.P65Warnings.ca.gov.
Exhaust Components
Exhaust components and exhaust hardware for cars, trucks, diesels, and import performance builds are stocked at Black Ops Auto Works. Shop exhaust gaskets, exhaust adapters, exhaust cutouts, exhaust valve controllers, exhaust hangers, exhaust wrap, oxygen sensors, exhaust brakes, and mandrel bend tubing for HEMI, Hellcat, Trackhawk, TRX, LS, LT, Coyote, EcoBoost, WRX, STI, and Cummins and Duramax diesel platforms. Every product is filterable by year, make, model, trim, engine, and drivetrain so the correct part ships the first time. Black Ops Auto Works carries 580 exhaust component SKUs across gaskets, hangers, cutouts, sensors, and fabrication supplies. What This Category Covers The Exhaust Components category groups the small parts that hold an exhaust system together and make it fit right. This includes exhaust gaskets, flange hardware, hangers and mounts, wrap and heat shielding, electronic valve controllers, oxygen sensors, exhaust brakes for diesel trucks, and raw mandrel...
View Exhaust Components Products
Exhaust Hardware
Exhaust hardware, V-band components, clamps, gaskets, studs, bolts, hangers, springs, and fabrication supplies keep custom and replacement exhaust systems sealed, supported, and serviceable. Shop stainless clamps, weld-on flanges, exhaust springs, manifold studs, tube sections, hangers, heat-resistant fasteners, and repair hardware from Vibrant Performance, Stainless Bros, Ticon Industries, Mikalor, DEI, and more. Every product is filterable by year, make, model, trim, engine, and drivetrain where application data is available, helping the correct part ship the first time. Black Ops Auto Works carries 49 exhaust hardware SKUs across fitment-specific replacements, performance upgrades, service parts, and installation hardware. What This Collection Covers Exhaust hardware is the finishing system for a cat-back, downpipe, turbo-back, header, or custom fabrication project. The correct clamp, flange, gasket, hanger, and fastener choice helps prevent leaks, rattles, and seized hardwar...
View Exhaust Hardware Products
Exhaust Systems
Performance exhaust systems for cars, trucks, SUVs, and Jeeps are stocked at Black Ops Auto Works. Shop cat-back systems, axle-back systems, turbo-back systems, headers, downpipes, mid-pipes, mufflers, resonators, catalytic converters, exhaust tips, exhaust valve controllers, oxygen sensors, exhaust brakes, and motorcycle and powersports exhausts for Mustang, Camaro, Challenger, Corvette, Silverado, and Super Duty platforms. Every product is filterable by exhaust position, material, pipe diameter, and vehicle year, make, model, and trim so the correct fitment ships the first time. Black Ops Auto Works carries 7,441 exhaust SKUs across every position of the exhaust system. What This Category Covers Exhaust upgrades change sound, appearance, and in some cases power. Exhaust fitment depends on engine, drivetrain, and factory exit position, so confirm the exact platform before ordering any exhaust component. Exhaust Position Cat-back, axle-back, turbo-back, and header-back systems e...
View Exhaust Systems Products
Kooks Exhaust
Kooks Exhaust parts and accessories for American muscle cars and performance trucks are stocked at Black Ops Auto Works. Shop stainless steel long tube headers, shorty headers, catted connection pipes, mid pipes, X-pipes, H-pipes, cat-back systems, axle-back systems, resonator deletes, GREEN catalytic converters, O2 extensions, clamps and header hardware for Mustang, Camaro, Corvette, Challenger, Charger, Silverado, F-150 and Ram HEMI builds. Every product is filterable by year, make, model, trim, engine and drivetrain so the correct part ships the first time. Black Ops Auto Works carries 174 Kooks exhaust SKUs across vehicle-specific fitment, performance upgrades, replacement parts, installation hardware and custom build needs. What This Collection Covers Kooks builds vehicle-specific stainless steel exhaust components for naturally aspirated, supercharged and turbocharged V8 street cars, track cars and HD truck builds. The range includes complete header-to-tailpipe paths as we...
View Kooks Exhaust Products